Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I use nRF52840 and SDK16 with S140 softdevice. I need 3 ADC ports. The initial code as follows.
static void adc_configure(void) { ret_code_t err_code = nrf_drv_saadc_init...
Hi,
I add a my .ilb file in the ses project .When I c all the function in the .lib file and build, it will have an log "undefined reference to 'xxxx'". But i can success...
I want to upgrade a BLE peripheral firmware (nrf52840) by using another nrf52840 as BLE central.
Do you have any idea how I can do that?
I know how to use android to upgrade...
Dk 0.8.5 with external GPS antenna modem FW: v1.1.1 nrf tag: v1.2.0 supl: v0.5.1 OS: Windows10
Put supl folder to "\ncs\nrf\ext\lib\bin\supl" * the path written in readme...
Hi,
I have a problem where I have to put a delay for 50 us after nrf_drv_rtc_counter_clear(&rtc); to get 0 counter from nrf_drv_rtc_counter_get(&rtc);
seems that the...
How to extract MQTT message from the Simple_MQTT sample for nrf9160-DK?
I am trying to use a specific message to trigger an action based on a predefined string. Not sure...
Hi,
As far as I understand, every connection establishment has to start with advertising.
Event if I have already connected and bonded to a peer, after disconnection...
Hi everyone,
I am using an nRF52840 dongle (MakerDiary) with SDK15.0 & SoftDevice S140 v6.0.0, and trying to change the BLE advertising manufacturer's data with the information...
Hi,
I am sampling a moisture sensor using one of the analog pins without issues. However, since my circuit is battery powered, I need to account for voltage drop of a 3V...
I have an nrf9160 dk on the latest firmware (i.e. mfw_nrf9160_1.1.1) and I have been unable to establish stable connection to LTE network using iBasis SIM. I tried using the...
Hi,
I am trying to follow this tutorial ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/ncs-tutorial---temporary ) on Nordic...
Hi,
I am facing the same issue of case 244574 , we tried to fix it follow your advice but failed. Here is my code:
After the first reboot of modem FOTA, the application...
Hi,
Recently updated with " nRF Connect SDK V1.2", after that AT Commands is working only with nRF connect link monitor SW. Its not working with teraterm,putty. In tera...
Hi
I am using the SDK_16.0.0 and SDK_for_mesh_4.0.
Board: PCA10056, nRF52840.
1) I try to send strings to from the nRF to PC and then, using a python script, poll...
