Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I'm trying to read temperature sensor data through TWI (I2C) from SHT3x using NRF52-DK and SDK v16.0. Observing an oscillator, the address and the return value with CLK looks...
Hello team,
Due to very constricted space on PCB, I am sharing one green LED between to IC's.
U1 is the NRF52832, and U2 is a Lipo Battery Charger IC. I want either one...
Hello,
I am working on the Nordic DFU to develop a bootloader for OTA update on our product.
So far I just ported the Secure Bootloader from Nordic examples. No functionality...
Hello!
I am trying to understand why the HFCLK of the DecaWave DWM1001C module based on nRF52832 has a significant (7000-10000 ppm) frequency offset w.r.t. its nominal value...
Hi
I use SES and nRF52832 dongle . I want to send data on "ble uart" and get that data on "nRF UART v2.0" app. mean i want send a string in program while every 5 second...
I'm working on modifying an existing app written on a custom nRF52832 board. The app uses softdevice s132, and was written for SDK14.2. The app was originally written with...
It seems that the PEER ID is managed by the PEER MANAGER. Can I manage this information myself? For example, I save this information (ADDR IRK) after the connection event...
Using SDK 15.2.0, s132, nRF52-DK.
The logging facility in Segger Embedded Studio tells me that the call to nrf_sdh_enable_request() takes about 500 ms. I have an interrupt...
Hi,
I was following your guide to implement a secure boot chain ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_bootloader.html ) and therefore build...
Hello,
I have a simple question. So, I'm trying to write some manufacturing information into the UICR but once I write to these addresses I can't see the device via bluetooth...
Hello,
I am using the UBLOX EVK-NINA-B406, which has the nrf52833. I have attempted to use Softdevice S140 and S113 (using the nrfConnect programmer. Soft device versions...
I want to interface the nRF5340-PDK board to a different vendor's board that runs at 3.3V.
I'm using the SPI bus to communicate between the two boards
Using the nRF5340...
I don't have absolute proof yet, but I'm 90% certain that the carrier LWM2M (0.8.1+build1) has a memory leak when used with a +CEREG notification level higher than it is expecting...
After much searching this site for a solution I'm at a point were I decided it necessary for me to ask directly.
SDK16.0, S132, windows 10 / SES, nrf52DK
I'm able to connect...
