The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
Hello, I am developing a Python script (Windows 10, Python 2.7.16, pc-ble-driver-py 0.12.0) to use a NRF52840 board to simulate the BLE part of an application running on a...
Hi,
I'm working on the nrf52832 development board and SDK 16.0. I want to use the Power supply supervisory functionality to detect any type of power failure.
I'm using...
Hi,
The example is currently printing the device address
on_adv_report(ble_gap_evt_adv_report_t const * p_adv_report) { ... NRF_LOG_INFO("Connecting to target %02x%02x...
I am going to find out an ideal throughput of NRF52832. And my environment is NRF52832/S332/MTU 247/connect interval 20ms.
Finally, i got a maximum value about 23Kb/s. I...
I have a nRF52840-PCA10059 dongle.
I have a PCA10040 dev boeard on which I programmed the ble_app_hrs_freertos_pca10040_s132 example after I modified HEART_RATE_MEAS_INTERVAL...
Hi,
I have some code which is based on the ble_app_gatts_c example sdk 15. I am using a Nordic NRF52840-dk pca10056 s140. Coding in Segger.
I want to each second change...
Hi,
I want to set the unused pins to low Level, however without using Software to do so, i.e. this has to be done before the chip is turned on.
How can I do that? Is...
Hello all, I have a little problem.
I`m trying to do an gateway communication using my NRF9160. The routine I`m trying to accomplish is next : -- Send message over serial...
Hi... i am getting the data through the RX,TX which is externally connected to the nRF52832 development kit , now i want to store the continous incoming data to the variable...
Hello, I am using nrf52840 board and SDK 16.0.0.
I am trying to merge this calendar example ( https://github.com/NordicPlayground/nrf5-calendar-example ) into ble_app_template...
1. I am trying to test the QSPI flash performance in nrf52840_DK ,but the QSPI init failed because of the event ready check,can i turn off the event check process?
2. I...
The recommended circuit in the v0.5 nRF5340 product spec differs a little from the nRF5340-PDK and I'm trying to understand the minimum requirements for an antenna. The spec...
Hi everyone, I am a beginner with the nRF52840 and I am looking at the example spi_pca10056 on SDK 16.0.0. What I've noticed is that at sdk_config.h file the pin configuration...
I have a question about what functionality is handled in the modem firmware vs. the application firmware.
I see from the nRF Connect SDK that the nRF9160 application communicates...
