Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
To Nordic support team attention,
Hi guys, in sdk16 there is ble_app_gls example. I slightly modified it so to have BLE_GAP_IO_CAPS_KEYBOARD_ONLY as GAP IO Capabilities...
Hello, we have an application with BLE. We've prepared secure bootloader with Serial Transport for performing DFU. Now we need to add necessary changes in application to support...
Hi everyone,
I want instead of MAC address to advertise my device using its 64bit unique ID. What I am considering, is to use the p_data array for that purpose and more...
Hi, I see an interesting situation.
I got flash corruption with values 0xff after random power cycling and it's happened only if I have flashed the bootloader
soft device:s132
sdk:15.3.0
I implemented the following, but the event does not occur even if the voltage is V2.8 or less.
Do you know the reason?
===
NRF_SDH_SOC_OBSERVER...
The nRF5 SDK's throughput sample (ble_app_throughput) provided very convenient shell commands to configure key parameters affecting throughput in a connection, such as ATT...
Hello,
in my project I have a custom board with a nRF52832 chip, which reads 4 channels with a sample rate of 1kHz (1ms). The SAADC readings get transmitted to a nRF52840DK...
soft device:s132 sdk:15.3.0 board:nRF52832 board (taiyo yuden EYSHCNZWZ)
Unable to receive event 'NRF_EVT_POWER_FAILURE_WARNING' I implemented the following, but the event...
Hello
Using the timer, I am making code that turns on LED1 to 3 sequentially. I thought it was going to be very simple, but it's not going as well as I thought.
I'm making...
Hi, I have very STRANG issues. I am adding custom Characteristics to custom Services. I have added 10 custom Characteristics with the same config 8 of them are working perfectly...
Hi,
I am on ncs master branch, when i build and load the Serial LTE Modem(SLM) application the application struck at mcuboot
The only additional configuration option i...
I am using nrf52840 board. I hvae interfaced a gsm module(quectel m66).The problem is my device gets an APP_UART_FIFO_ERROR after every few sms commands.The maximum data i...
Hello everyone!
I have an issue about upgrading firmware over Bluetooth LE with a mandatory pairing of devices. I want only paired devices to have the ability to upgrade...
hello,
In the nrf51822 sdk 5.1 I can see a routine named ble_app_ibeacon.
I find a parameter define as below,the data is added to the advertising data.
#define APP_MEASURED_RSSI...
