Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Dear Sir/Madam,
We are «SMART Solutions», Ltd. a startup from Tomsk, Russia.
Our company developed iBack Posture Corrector please see http://en.iback.online/ .
The device...
Hi Nordic team
I tested the example [802_15_4\wireless_uart\raw\first ] period 1s send 20 Byte data to example[ \802_15_4\wireless_uart\raw\second ]serial tool to printf...
Hi
I am working on a project based on Thingy91. Is there any sample application in NCS SDK to show the communication between the two SoCs on the Thiny91. I will need to...
Hi all,
I migrated my nRF52840 examples from SDK 15.2 to SDK 15.3 folder and when I tried to build
the examples and I discovered that nrfx_power_clock.c could not be found...
Hi
I am working on the Connectivity Bridge project using Thingy91. I noticed that the Thingy91 shows up as a USB drive that has four utility files, readme.txt, config.txt...
I am trying to hook openthread with freeRTOS.
Short story: the current state of my implementation is that I get a hardfault after succesfully calling mqttsn_client_search_gateway...
Hello,
I've added quite a few interfaces and endpoint configurations and I'm trying to figure out how to properly respond to "Get Descriptor" Setup packet that requires...
Hi, I am using nrf5832 sdk 14.2 where I am trying to scan the data and advertise same data with some modifications. I have used Central and Peripheral example ble_app_hrs_rscs_relay...
Hello,
I am trying to compile the samples from SDK_for_mesh_v4.2.0 but i have problem with my environment set-up. I am following closely the documentation but I think something...
Hi everyone,
We have three ADC channels, two of them are implemented as a simple ADC without oversampling, the third one uses oversampling. Because one of them use oversampling...
Hi, I have started development on nrf52840DK . 1-I have installed nrf Connect SDK v1.3.0.
2- I have also installed Segger Embedded Studio Nordic Edition. and selected nrf...
Hello, Please help i m trying to share memory between Network and App Cores in a nrf5340
How To do?
at page 21 Figure 2 Memory Map
it seems that FLASH address 0x0000...
Dear Sir.
Some problem with the PWM .
Pwm output on pin 12 is connected to a buzzer.
When pwm_pin_set_usec(pwm_dev,PWM_IO, 260, 130,0) is set through the pwm_init...
I'm trying to achieve half-duplex UART communication between two nRF52840-DK:s (master/slave) using no external circuitry. I was looking at the thread https://devzone.nordicsemi...
Hello
I am using SDK16, and using BLE sample project (central app_ble_blinky)
when I am taking sample project without BLE , I am able to add UART secure bootloader...
