I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Dear nordic,
I need a advise from your side. my custom board has two spi device both are working same line. one is SD card interface and other is sensor which works in DMA...
nrf9160-DK to NB-IOT service at vodafore UK
```
[00:00:00.322,479] [0m<inf> asset_tracker: Connecting to LTE network. [0m[00:00:00.329,193] [0m<inf> asset_tracker: This...
I know that we have actually some countries in Europe which don't support LTE-M, therefore we like to have a fallback.
Does there exist a fallback option to GSM or EGPRS...
Hi,
So I was having an error which caused my application to stall in the "do_stop_check" part of the nrf_drv_twi.c file, so I added a bit of code to check if I could figure...
We have a device with the following configuration:
nrf5_SDK_for_Mesh_v3.1.0
nRF5_SDK_15.2.0
s140_nrf52_6.1.0_softdevice
mesh_bootloader_gccarmemb_nrf52840_xxAA ...
Hi,
I'm trying to make a script in Python using the nRF52840 dongle, to make some BLE advertising.
I'm using:
- Python 3.7.2 (32 bit)
- pc_ble_driver_py library
...
Hi everyone,
I'm using ses IDE to debug via J-link on nRF52840 DK.
I'm debbuging CDC ACM example ( I haven't changed it ) but when I debug: ret = app_usbd_cdc_acm_write...
I am designing a PCB for the nRF52833 aQFN chip. To reduce the cost of the PCB I would like to fanout the inner row of the IC package on a single layer by using 3/3mil traces...
Hello,
I have a certificate attached, but in my personal account it gives an error when I enter the DK data.
Please tell me why the error occurs?
OS: macOS 10.13.6 ...
Hi,
I am using IM69D130 MEMS sensor with nrf52832 I just want to confirm the output of pdm sensor . please any one suggest how should i proceed . how do i code for it ?...
I am attempting to migrate my BLE project to a higher security level with bonding. Was mode 1 level 2 and am upgrading to mode 1 level 4. When I change the configuration to...
Nrf52832 chip is used, and the software package is the “nRF5_SDK_16.0.0_98a08e2” version.
According to customer feedback, Bluetooth connection is generally unstable...
