I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi,
I noted that the CW generated in the %XRFTEST TX test seems to be offset from the requested frequency. Specifically, issuing the command
AT%XRFTEST=1,1,20,8500,-50...
Is there still no way on this build to setup zerocrossing detection?, I mean using interrupts I developed a zigbee dimmer that detects zero crossing and dims 3 separate channels...
Hi,
We are using NRF52840 Dk board to transfer the data at 10ms through Bluetooth which is central and peripheral as other cc250moda controller Bluetooth. Our objective...
Hello:
I am porting the LESC with MITM security protocol from your "ble_app_multirole_lesc" example inyo a project that runs FreeRTOS. This is on an NRF32540 With s140...
Hi,
I'm using an nrf52840 dk to query another device over spi and then pipe the response back USB to a host PC. Ideally, we're piping data at 1 Mbps (which should be very...
Hi,
We are using nRF9160 DK. Loaded the asset tracking application, and followed all the procedure to connect to nRF cloud.
In nRF cloud i can see the data in the cloud...
Hello,
I am currently designing a custom PCB with the nRF8001 chip. For a smoother assembly and component procurement, I am looking to make all the resistors on the board...
Hi there,
I have a problem with the bootloader from the RF5_SDK_11.0.0_89a8197 together with Intel Wireless Bluetooth chipset.
I use the softdevice s132_nrf52_2.0..1. I have...
Hi im after the library driver for the nRF509 using Arduino but when i go to the webpage to get it the webpage says not available can someone advise please
Many thanks ...
Hello,
Is it correct, that periodic advertising is working only with non-connectable mode? To implement periodic advertising with connected mode I need to start the second...
Hi, I tested a simple client-server UDP application, using as a template the UDP examples from the SDK. The UDP server is running in a nRF52 board and the client is a Python...
Hi,
my goal is to send data to the Google Cloud Platform using CoAP.
I found this example:
https://infocenter.nordicsemi.com/topic/sdk_tz_v3.1.0/thread_google_iot_coap...
Hi,
Recently I have been working on nrf9160 and wanted it to work as a modem for a linux computer for example raspberry pi. The aim here is that I connect the nrf9160 to...
Hi,
We are using nRF9160 DK. On the Arduino connector, we connected STM X-Nucleo-IKS01A2 sensor shield. We wanted to fetch the sensor values using nRF9160.
What example...
Dear Sirs, good night
Currently developing hardware using nRF52840 based module (BT840X from Fanstel)
Wanted to ask if following assignment would be OK for controlling...
