I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
I am trying to set up a region of RAM to store variables that persist across soft reboots but am unsure how to do it in this environment. I would normally define a region...
Hi Nordic ppl,
Is Nordic SoC supporting BlueZ package ?
Any specific SoC that we should be selecting to be able to run the .
Also, i believe all 3rd party Modules...
I am trying to implement openthread cli uart in pca10059, have made all modifications but the hex file is not getting burnt in bootloader mode using nrfconnect
/cfs-file...
Hi:
I use the PCA1004 EVK bord to configuer the I2S MCK as 256K, 32MHz/125 (I2S_CONFIG_MCK_SETUP 34340864) .
then I measure the pin use oscilloscope, but I only get 255K...
Hi Nordic support,
We had an "intermittent" connection failure with a BLE radio in one of our products under development, which exhibited itself with an <unknown> device...
Hello,
We want to use the flash to store two types of information: application configuration settings (which should be protected during DFU) and temporary data (which...
Hi,
I m using nrf52840 and m doing DFU over serial.
one side is master controller and other end is NRF DFU serial(secure bootloader uart debug code).
After sending init...
Hi everyone,
I am trying to connect to a smartphone in an extended advertising using the firmware created under the following conditions. However, there are no event notifications...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am making an example of periodically reading sensor data using SPI.
The SPI is triggered through...
Currently I am using a PCA10040 to do some prototyping for a custom board. I intended to use the nrf52832 to interface with a HDC2010 (TI) temperature and humidity IC over...
Hi,
I was using SDK v1.1.0 for a while and am updating my project to SDK v1.2.0. I see that there is also a release for v1.3.0, however, there are too many application and...
I have tried to setup the time cluster, with:
ZB_ZCL_TIME_SET_REAL_TIME_CLOCK_CB(time_set_rtc);
But whn I do it, I lways get linking errors, since zb_scl_set_real_time_clock_callback...
I had a continuation question to this.
https://devzone.nordicsemi.com/f/nordic-q-a/64457/scheduler-for-thingy-91-using-nrf9160-dk
Is there any sample tutorial for the...
I don't think this is possible at the moment but worth putting it out in the wild:
Currently the binary image sizes for nRF9160 using Zephyr can get quite hefty. Is there...
