Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi all :) ,
I'm trying to create my new zip folder with new image.
I connect to my nrf52833, then i click on dfu button into nrfConnect mobil app.
I selec zip file...
I'm using:
OS : Windows 10
IDE : Segger Embedded Studio for ARM Realease 4.52c Windows x64
SDK : nRF_SDK_15.0.0_a53641a
In my project I'm using 4 pressure sensors...
Hi,
I've been trying to make a small modification on the existing Nordic Thingy firmware, such as changing the color of an LED, by compiling the existing Nordic Thingy 52...
Hi,
I am trying to set up a region of RAM to store variables that persist across soft reboots but am unsure how to do it in this environment. I would normally define a region...
Hi Nordic ppl,
Is Nordic SoC supporting BlueZ package ?
Any specific SoC that we should be selecting to be able to run the .
Also, i believe all 3rd party Modules...
I am trying to implement openthread cli uart in pca10059, have made all modifications but the hex file is not getting burnt in bootloader mode using nrfconnect
/cfs-file...
Hi:
I use the PCA1004 EVK bord to configuer the I2S MCK as 256K, 32MHz/125 (I2S_CONFIG_MCK_SETUP 34340864) .
then I measure the pin use oscilloscope, but I only get 255K...
Hi Nordic support,
We had an "intermittent" connection failure with a BLE radio in one of our products under development, which exhibited itself with an <unknown> device...
Hello,
We want to use the flash to store two types of information: application configuration settings (which should be protected during DFU) and temporary data (which...
Hi,
I m using nrf52840 and m doing DFU over serial.
one side is master controller and other end is NRF DFU serial(secure bootloader uart debug code).
After sending init...
Hi everyone,
I am trying to connect to a smartphone in an extended advertising using the firmware created under the following conditions. However, there are no event notifications...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am making an example of periodically reading sensor data using SPI.
The SPI is triggered through...
Currently I am using a PCA10040 to do some prototyping for a custom board. I intended to use the nrf52832 to interface with a HDC2010 (TI) temperature and humidity IC over...
Hi,
I was using SDK v1.1.0 for a while and am updating my project to SDK v1.2.0. I see that there is also a release for v1.3.0, however, there are too many application and...
