Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I use sdk16 on nrf52810 for development, but I want to use long broadcast packageada. What should I do?
A short broadcast packet can only be 31 bytes
thank you!
To the kind attention of Nordic support team,
I was reading in peer_manager library that when a ble connection is established, using the connection handler as a parameter...
Hi ,
In our actual design, we are using nrf52810. We have done all our development on nrf52832, as there is no Eval Kit present for nrf52810. We are porting our development...
Hello,
I can see RTC drift of around 14 seconds in 1 hr when I select the internal RC oscillator in sdk-config of nrf-calender example.
Is this much drift expected? In...
I would like to add events for button release and button long push to my application. I also want to keep the SDK folder unmodified for easy upgrades.
To do this I copied...
Hi,
In my project, I am using High voltage mode [VDDH] in this case automatically REG1 [LDO] will be enabled. But my question is as per the datasheet i understood that even...
Hi.
I am developing using nRF52820 example source using SDK 17.0.2.
USB and LESC were added using S112.
However, during operation, the following HardFault error occurs...
Hi everyone,
I am trying to integrate the DFU service into my application on order to achieve buttonless OTA DFU but I am not able to implement it so far and I need your...
Hello,
I merged the two projects usbd_cdc_acm_pca10056 (A) and ble_app_hids_mouse_pca10056_s140 (B) by copying all additional contents from A's flash_placement.xml into...
Hello,
I am trying to send data obtained from a SAADC port via BLE using the ble_nus_data_send function. This must happen periodically at frequencies within the Gigahertz...
As we know, NRF9160 supports NB network and has an IMEI number itself. Now I want to know whether I can manage this IMEI number, such as reading, writing or modifying. In...
HI all,I am looking for a help.how to start SPIM RX task immediately delay less than 2us？
I have a SPIM test on 52832 DK board(QFAAE0) with SDK16.0, the MISO pin has connected...
Hello
I have a question about the Bluetooth multipairing function using nrf52832. How do I use this feature? And up to how many connections can I make?
Thank you!
I am going to store some informations into UICR.
In case, wrong data wrote have to correct we need to rewrite it.
I have been searched the forum and the answer shows ...
