I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
I use sdk16 on nrf52810 for development, but I want to use long broadcast packageada. What should I do?
A short broadcast packet can only be 31 bytes
thank you!
To the kind attention of Nordic support team,
I was reading in peer_manager library that when a ble connection is established, using the connection handler as a parameter...
Hi ,
In our actual design, we are using nrf52810. We have done all our development on nrf52832, as there is no Eval Kit present for nrf52810. We are porting our development...
Hello,
I can see RTC drift of around 14 seconds in 1 hr when I select the internal RC oscillator in sdk-config of nrf-calender example.
Is this much drift expected? In...
I would like to add events for button release and button long push to my application. I also want to keep the SDK folder unmodified for easy upgrades.
To do this I copied...
Hi,
In my project, I am using High voltage mode [VDDH] in this case automatically REG1 [LDO] will be enabled. But my question is as per the datasheet i understood that even...
Hi.
I am developing using nRF52820 example source using SDK 17.0.2.
USB and LESC were added using S112.
However, during operation, the following HardFault error occurs...
Hi everyone,
I am trying to integrate the DFU service into my application on order to achieve buttonless OTA DFU but I am not able to implement it so far and I need your...
Hello,
I merged the two projects usbd_cdc_acm_pca10056 (A) and ble_app_hids_mouse_pca10056_s140 (B) by copying all additional contents from A's flash_placement.xml into...
Hello,
I am trying to send data obtained from a SAADC port via BLE using the ble_nus_data_send function. This must happen periodically at frequencies within the Gigahertz...
As we know, NRF9160 supports NB network and has an IMEI number itself. Now I want to know whether I can manage this IMEI number, such as reading, writing or modifying. In...
HI all,I am looking for a help.how to start SPIM RX task immediately delay less than 2us？
I have a SPIM test on 52832 DK board(QFAAE0) with SDK16.0, the MISO pin has connected...
Hello
I have a question about the Bluetooth multipairing function using nrf52832. How do I use this feature? And up to how many connections can I make?
Thank you!
I am going to store some informations into UICR.
In case, wrong data wrote have to correct we need to rewrite it.
I have been searched the forum and the answer shows ...
