Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I am trying to modify the receiver an transmitter examples to change the default bandwidth on both the receiver and transmitter. I have looked through documentation without...
What is the communication distance of NRF52832 Bluetooth reference? Since nrF52832 is used for the first time, we are not sure about its performance. Is it possible to reach...
Dear Team,
I am try to customize the some of the parameter of HTS221 temperature and humidity sensor used in thingy52 board, However if I change any of the parameter then...
I am using the nrf connect desktop application on windows with a PCA10059, and have found the application to be buggy when receiving a flood of notifications, this works fine...
I've been logged in for about a week now, and still can't log out.
I left a posting about that almost a week ago with some "bumps" later on the "back stage" section, but...
Hi!
Can anyone tell me that isthere any app which logs data automatically into txt or csv file from nrf52???
I am getting data at nrf connect but every time i need to...
PCB : thickness 1 t(1mn), 1/2oz, 2 layer
The antenna was removed and the VNA was connected between L3 and C6.
The impedance was about 100 ohms.
The part value is shown...
We have a latest set of prototypes which use an NRF52840 on a Laird BL654 module.
On two of these protoypes the module is unresponsive. We are using a J-Link Lite module...
Hi,
I was using nRF Mesh application to get the data of uint32_t from my server model(nRF52840) but nRF Mesh android application crashes while sending the opcode to the...
I am searching for complete developement kit and SDK support which can be used to form BLE mesh Network and BLE beacon device. The idea is that BLE mesh nodes will act as...
Good afternoon, dear Sir of Madam.
Our product used the NRF21540-QDAA-R7 which has gone obsolete. What is the best substitute part?
Unfortunatelly i couldn't find substitution...
Hi I am facing a issue regarding the DFU update using the nrfConnect App.
Since we recently updated from SDK12.0 to SDK16.0 and the softdevice version has been changed in...
Hi,
I am analyzing the power consumption of mesh nodes using your Power Profile Kit. I am running the example beaconing of the Mesh SDK 3.1.0 on a board nRF52832 with the...
I have designed a nrf9160 debugging board, which uses 18 and 19 pin as the log output. Then I also configure the TX and Rx of UART0 in the overlay file, which are 18 and 19...
