Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Will the nrf52811 I2C compatibility work with the I2C on the MLX90614 IR sensor. I need to make sure that they will work with each other without issue. Below is the datasheet...
I have DFU OTA application running on 52840 platform on a custom board. SDK v15.3.0. I use SoftDevoce S140 v6.1.1.
Then I need to port it to 52832 platform - SoftDevice...
I have used the NRF52 before, but we got a new need for it to be used with FreeRTOS. Usually I use the RAM_START and RAM_SIZE defines the set up the ram usage for the soft...
1. I tested the following AT instruction on ncs v1.3, returned OK, but did not return the subscription message, need to modify where to return the subscription message did...
We are using I2C bus for communication with a RTC and Accelerometer. But sometimes the I2C get struck in i2c_write. It does not happens always it may happen randomly. We are...
Hi,
I just spent several hours trying to figure out why, using a nRF52 dev kit w/ SDK13 + S132 on both central/client and peripheral/server side, sd_ble_gattc_read() was...
Dear Support,
I have a question about the IPv6 networking with OpenThread. I do have an mesh network with about 50 nodes (PCA10059) and implemented CoAP servers and clients...
I just downloaded SEGGER Embedded Studio (ARM V4.52c) and plugged in my rather old PCA10040. It offered to upgrade the driver, which I accepted. Now, when I click "Connect...
Hi,
Just installed nRF Connect v3.4.1 on a macOS Catalina and get the following error message when starting any of the apps:
I've tried both reinstalling and downgrading...
Hi,
I'm making a peripheral device that needs to minimise battery usage.
My device is essentially a beacon but it allows temporary connections to send a stream of data...
Hello,
I have purchased a new nrf52832 DK board for development. I tried to run some examples like ble_app_blinky which are working properly. But when I tried examples such...
Dear All:
Our team are ready to develop a project with multicentral and multiperipheral
The project topology image lists as follow:
I want to ask how many ram it will...
I know this sounds a crazy question but is it possible to flash a custom nRF52832 board with the same firmware that is shipped with the dev kit and create a mass storage out...
Hello,
I am looking to run the ble_app_uart example from the SDK v17 in nRF only mode on the nRF52840 DK. When running the application as is on nRF only mode, it fails during...