In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi,
I'm trying to add a custom service to a working application that has a working battery service.
I have followed https://github.com/NordicPlayground/nRF52-Bluetooth...
Hello.
I am testing UART using ble_nus_data_send function.
However, it has different length data was sending from each trial.(ex. 0, 4095...)
In the ble_nus_data_send...
Hi sir,
I am using ble_app_uart to send the enegry value to the mobile. for energy calculation i am using internal rtc oscillator but after 179 secs the device stops working...
For example, I get logs like this, and I want to know what these events are:
ble_cts_c: BLE event handler called with event 0x57
I also see 0x36, 0x12, etc. when the CTS...
To the kind attention of Nordic support team,
after doing some ble bonding between an nRF52 device and an host computer, I can see this situation in device flash. So, these...
Hello,
I am trying to develop a sensor which can connect to multiple sensors and send the data which is received by its UART through bluetooth, at the peripheral. Central...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
when i copied the spi_fujitsu_fram example to my project folder on c drive, i am getting this error "zephyr/linker.cmd:70 cannot move location counter backwards (from 0000c23c...
Hello!
I would like to know if there is any way to route the signal from the main LED from Nordic Thingy 52. I checked its data sheet and I only found the pinout for other...
After downloading nRF5 SDK v17.0.2, I checked the Release Notes - and they state SES v4.50 has "been used for testing".
So I downloaded & installed SES v4.50
The HID Keyboard...
Hi, recently I want to establish a connection between two development boards (STM32F103 + nRF52840-DK), that the STM32f103 board can create the data and send it to the nRF52840...
Hello, I have a project running on a PCA10040 board, using softdevice 132 (0x9D, v5.0), ble and serial port for data transfer.
I want to migrate this project from this...
I am trying to use the UART for a custom version of the DFU. I have it transmitting no problem, but I never get the RX_DONE event. I cannot see any reason and I have looked...
Hello,
I have a question because there is a problem with writing code using timer.
I wrote the following code to avoid using the LED timer when I first ran it.
However...
