I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello, everyone. I'm a novice who just started Nordic. My goal is to apply button input and timer to implement two functions with one button. (Based on the time the button...
Query on reference designs and layouts
1. "nRF52833-QDAA Reference Layout 1_0 PCB" stack-up seems to need improvement (please check the Core thickness between Layer1 and...
Hello, I'm a novice who just entered Nordic. I'm dealing with button input through bsp example now. And I am using sdk v17.
I succeeded in toggle LED by simply clicking...
Hi,
I am writing an APP for comunicating with my nRF peripheral. I've set the MTU size to 251 and this works fine under bluez or android.
But if I try it in iOS (>10.0...
Hi
I've been working on a project over the past few months, and per a new requirement I was asked to add a debug configuration, as thus far I have worked with only a release...
Hi,
We have a Lattice Ice40 UltraPlus FPGA, SPI FLASH, and nRF52832. We would like to be able to include the FPGA's binary image in our DFU package but it is about 110kb...
Hi,
We are using SES on Windows to program a nrf52832 device with a SDK 16.
We are having problems with the Secure BLE DFU. We are able to perform the DFU on our devices...
We're trying to minimize power consumption on our custom nRF52840-based board and we have some questions about the behavior of HFINT and HFXO. The specification says this...
Hello,
I am currently evaluating concepts on how I can power my nRF52832-custom-board with a LiPo-battery, in order to get a good tradeoff between lifetime and form-factor...
HI Team,
We are using the nRF52840 DK for our development purpose. We have some issues with USB J2 connector and unable to connect the on board debugger. We have tried...
Please note about 9 days ago another user reported similar problem but is his case LED3 and LED4 were blinking. In my case after reset I see LED 3 blink and then about 30...
It had been working fine until just this moment.
Every time i turn it on, it works fine for few seconds and then the red led in the device turns on. I don't understand the...
Hi,
I'm developing for a 52833 using SDK_17.0.0 and S113_7.0.1.
I'm using the following code with the intention that when the RDY pin goes low, it will wake up the processor...
Hi! I'm currently using the nrF52840 DK to send numbers by BLE. I have 2 questions for you. 1. Can I send negative values? ex. -1, -2, -3 2. Can I send decimal values? ex...
