Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hello,
I am testing the PCA10040 example project & modifying.
I was checked that the project works well in nRF52832 board.
Now, I want to download the project to nRF52810...
Hi,
I am using nRF 52 DK as a sniffer and monitoring the BLE traffic on Wireshark. The goal of this is to ensure that the communication is encrypted.
I can see that in...
I tested "ble_app_buttonless_dfu" example and "ble_app_beacon" example. Everything was fine. Now, I am trying to make an application that advertise as a beacon and supports...
Im trying to come up with a commercial low power sensor module using the nRF91 DK. What happens if i use my own Telstra SIM card, will it have access to NB-IOT in South Australia...
I use Android nRF Toolbox Uart and NRF52832（SDK version ：17.0.2，app：ble_app_uart）。
I set （RX＆TX）PHY 2M，（11.25-15,0,20S）。
form NRF52832 send data to Android nRF Toolbox...
Hi guys
I try to develope a bluetooth application with a customboard on Zephyr 2.4. At the moment the firmware should work on the nrf5340-pdk until the hardware is ready...
Hello NordicSemi,
We are developping a product based on the nRF52840-QIAA and are using the schematic reference nRF52840 DK Hardware files which is similar to the circuit...
I have developped an application using bluetooth mesh with NFC to read a text record. I am currently using the nRF52840 DK Rev 2.0.1 2020.11.
Regarding my software setup...
W e have the problem with GPS that it sometimes takes a long time after a cold start until the modem gets a fix. I see strongly fluctuating times between 78 s and> 600 s ...
I'm trying to modify the asset tracker for the Thingy91 to read the actual values of the ADXL362 and BME680 sensors. By default for some reason the project uses simulated...
Hi,
this project is upgraded from 51422, now use 52832, sdk 15.3 and sd332, we encounterd a issue that the ant burst always fail after first segment is sent while ble is...
Dear Nordic:
Help to see this problem，tks
Problem description:
SDK：nRF5_SDK_15.2.0_9412b96
status：bonded device
demo：Let's refer to this sample code ---- nRF5_SDK_15...
Hello, all.
I am working on a project in which the ultimate goal is to read an 8-bit signal with 10kHz frequency.
To test if this would be possible, I tried to generate...
I am able to put my board(nrf52840) in DFU mode with buttonless code using Esp32 as controller.
The problem currently i am facing is to send a init packet to my nrf board...
I'm running a fine working example based on the Bluetooth low energy Characteristics, a beginner's tutorial on the nRF52DK using SDK 15.3 working as a BLE peripheral.
When...
