In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello,
I'm trying to develop custom model for my bluetooth mesh application. I have gone through Creating new models document and I understood the procedure. But to integrate...
typedef struct __attribute((packed)) { uint8_t on_off; /**< State to set */ uint8_t tid; /**< Transaction number for application */ uint8_t transition_time; /**< Encoded transition...
Hi, We're connecting to our server over LTE and then immediately starting GPS search. The modem is in LTE+GPS mode. As we understand it, the GPS will do nothing for about...
<environment> - Windows10 - modem fw v1.2.0 - nrf v1.3.0
I try to get mnc and mcc data but no luck. Any help?
I also tried it using modem_info_params_init and modem_info_params_get...
There are 10000 posts with this problem. I have imported someone else's project, and the file exists at Keil_v5\ARM\Packs\ARM\CMSIS\5.7.0\CMSIS\Core\Include exactly where...
Hi all,
I've been trying to get BLE up and running on our custom board after writing firmware on the DK. I am able to get other peripherals on our board up and running ...
Hi guys,
I am a long term Nordic user since SDK12 and i know that Nordic does not support MbedOS by any means but maybe you could help me try and understand what needs to...
Hello,
I've a very strange problem with the nrf52838 chip in the ISP4520 ( https://www.insightsip.com/products/combo-smart-modules/isp4520 ).
The nrf52832 advertise...
Hi,
I need to sample ultrasonic signal with PDM microphone. I would like to use NRF52840 PDM module and configure it for sampling frequency of 96KHz. Is it possible? Also...
Hi,
I have used BMD301 BLE chip. I have connected one wifi chip "ESP02" with BMD301 chip via UART.
I am using nRF5_SDK_15.3.0_59ac345 for my ble application firmware...
Hi,
we have a nRF52 DK getting sensor values from a Sensor connected as SPI-Slave. Everytime there is a new Sensor Value (~20 ms) the sensor generates an Interrupt and pulls...
Hi,
While upmerging our project from SDK 15.3.0 to 17.0.0 we faced an issue in the sdc_handler due to usage of a NULL pointer.
In the case SDC_EVT_INIT if the p_event...
Hello,
I am experimenting with PWM for time, I have a setup where I am using three sensor which gives analogue output.
I am using a mux which has two control pins, so...
Hi all
I have just started doing some work with the nRF52840- DONGLE (and hence nRF52840-DK) and am new to Nordic devices, tools, BLE, etc.
Basically for my first application...
