We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi all:
I am use ble_app_blinky demo sdk 16.0.0 I want to put system on idle mode,but there need to call two times sd_app_env_wait() so it can in system on idle mode.
...
Hey,
I am a new to BLE devices. I am using BL651 Laird Connectivity's 453-00005 module
and using standalone JLink OB ARM debugger to connect.
When I try to connect my...
Hi,
I want to get running the sample "lwm2m_client" on the board nRF9160DK (PCA10090).
Modem FW Version: 1.2.0.
I build the sample with Segger Embedded Studio v4.52...
Hello,
When I try to run a project containing a .cpp file, I get the following console output:
I am compiling the openthread client example with a slight modification...
Hello, I am trying to change the instance on the spi in the spi example, but unfortunately it is throwing me an error - implicit declaration of function 'NRF_DRV_SPI_INSTANCE_...
Hello,
I am using nRF52840 S140 v7.0.1. I have a query on Tx power settings.
1) In below snapshot under features, its mentioned as “4 dB steps”. So whether can I write...
Hello,
I previously used the latest SDK v17.0 on my nRF52832 PCA10040 board DK.
I ran the ble_app_uart example in order to understand how the Nordic UART Service works...
Hi all
I am doing a small personal project. I have 2 DK's :
nrf51 DK: pca10028
nrf52 DK: pca10040
Up until recently things worked fine, but suddenly i ran into a...
1. At present, using the Programmer burnmodem firmware in tool nRF Connect mfw_nrf9160_1.2.0.zip step is cumbersome.
2. Is there a simpler command line tool that can burn...
We have v0.8.2 of the nRF9160DK which has GPS antenna issues. We are looking to get the latest available version of the DK from Mouser/DigiKey. Is there any way to ensure...
Hi,
I want to use SPI to receive data from an ESP32 microcontroller to the nRF52840 development kit. Where can I find information/example regarding the same (I'm using nRF_SDK_17...
Hi
we have a custom board with nrf52810 chip, 32M crystal on it and using the zephyr version 1.14.1 as the firmware base.
Using zephyr samples/bluetooth/hci_uart
Custom...
