But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello, I want to inquire about the functionality of nRF52833-DK if I want to communicate between transmitter and receiver for locating position of receiver using BLE (Bluetooth...
Hello ,
I am interfacing the nRF52832 with winband spi flash . I can able to read the device manufacture id but i couldn't able to read the data from the device . I am getting...
Hi,
I am using the nRF52840 to sample some channel.
I am using the nRF5SDK160098a08e2 for that and based on the saadc example.
These are the results for my tests....
Hi there,
I've been unable to find a good example of what settings are required specifically to ensure that a characteristic's value can only be read and notified in an...
I have a question regarding the nRF Toolbox App v5.0.2 on iOS 14.1 and the Cycling Speed and Cadence demo app. It appears to be that the km/h calculation based on the CSCS...
Hi
I have created 4 threads in nRF9160 application, I have to go to sleep if none of the thread is running.
For this how do I check whether the created threads are running...
Hi, We are working on nrf5340 with the nrfx I2S implementation. We have configured the I2S IRQ for every 5 miliseconds. However, we have observed that successive IRQ introduce...
We are testing the combination of hrs example and the code in the butonless example. When I tried dfu after putting the code together, this error occurred. What does this...
I am trying to interface the microphone with nrf52840 and using the PDM interface. After initializing the module (nrfx_pdm_init) and then set the buffer , I do see clock and...
Dear Sir.
I have some boards that work with nRF9160 and Chipsim.
Some work fine.
Using MQTT application
With two boards I get the errors.
ERROR: getaddrinfo failed...
I am new to the nRF5 SDK. This is my first time using nRFX SPIM so this may well be a beginner error.
I'm using SDK version 17.02 and I am using a nRF52840 module.
I...
Board: nRF52840DK
SDK: 15.3.0
Softdevice: 6.11
I am trying to increase the MTU size in order to read more data on the peripheral. I have tried to increase the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
The SDK version I use is 15.3. And I tried to add the following code to the ble_nus.c
But it didn't work.There is no characteristic 0x2901. I don't know what's wrong....
Hi, I'm investigating the current consumption of a new product that we are developing and have found
current spikes of 40mA every 24ms. The spikes occurs in unconnected...
HI,
I get confused using the ble terms hence i'll try to articulate my query as much as possible. I'm using the nRF52832 board and all i have one service with one characteristic...
