After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi all,
I'm having some trouble on figuring out how the UICR behaves and what I can expect from it. I am trying to lock the UICR from further modication. Based on the documentation...
Hi All,
I was trying to program a simple LED peripheral hex file to the nRF52840 dongle.
Initially I was modifying an existing sample program from one of the examples...
I am on Ubuntu 20.04 with SES 5.42c, SDK 16, and SoftDevice S140 version 7.0.1 I am using a Knowles SPH0645LM4H. I have put together a beacon that operates the microphone...
Hi,
We use TLS encryption with MQTT towards Amazons MQTT-service.
What we have been able to do, is send 1 packet (2KB max size, due to modem buffer limit set by Nordic...
Hi
I'm currently trying to use a cheap stlinkv2 clone flashed with https://github.com/x893/CMSIS-DAP for at test setup. (cmsis-dap enables it to remove APPROTECT/read back...
Hi,I need Tune-Up Information for all chanels and frequency ranges( "source based time average conducted power") incl. production tolerances for Nordic NRF 24AP2 IC.to be...
Hi..... I'm working with custom service and characteristic!!! I succeeded in changing the characteristic length like bellow. attr_char_value.init_len = 10; attr_char_value...
Hi,
I am trying to do some tasks based on a particular button press, below attached is the buttons_init() function and the button_evt_handler() function. Code compiles and...
For the nRF52805 how is throughput specified?
Throughput Spec:
"It is capable of Bluetooth high-throughput 2 Mbps" ( ref )
Is this spec for serial throughput...
Hi,
I'm trying to periodically send sensor data to the AWS server and followed the documentation here to connect and send data to the server. I use these configurations...
Hi!
I've been trying out a tutorial about adding custom service and characteristics ( https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello ,
I am having nrf52832 custom board.
In my project i need to use both CLOCK source ( Low frequency clock and High frequency clock source ).
Timer running on high...
Hello, Second time in here, thank you so much for all the support so far!
I'm developing a Beacon BLE, I wanna be able to send data over Advertising or Scan response. So...
I am trying to implement ble_app_interactive on nrf52840 as my application will require 2 uarts. I have started from the example application for the nrf58832 and created a...
in nRF52840, current consumption can be decreased by executing code from RAM instead of from flash. How is it possible to execute code from RAM? how to executing code from...
