Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I updated the nRF Connect SDK to latest master. It currently uses Zephyr 7d20f2ebf2. Most of the time (~4 times out of 5), calling sys_rand32_get() crashes the firmware and...
Does the ZBOSS stack have an API that provides network statistic or network health details? We would like to get a general understanding of state of the network.
Thanks...
Hi
I'm using SDK_17.0.2 with softdevice S132_7.2.0, can anyone advise DFU SD version code for this?
I can't find it in list below, the last version is S132_7.0.1, thanks...
Hi.
I am developing on a custom board using nRF82820 / SDK 17.0.2.
A project was created by modifying examples \ble_peripheral\ble_app_gls.
There is no project for...
Hi,
I am trying to use nRF connect desktop with nRF52840 dongle.
But, in Bluetooth Low Energy app, when I select connected dongle in the drop down list, it always return...
Hello,
My sensor based on nRF52833 will have soldered non-rechargeable battery and it will be potted in resin compound to insure waterproofing.
I wonder, what if for some...
Dear community, good afternoon
We have been working with a coordinator, a router device and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b...
Hi,
I'm currently trying to load my firmware into some custom nRF52832 boards. It seems that several of them have been locked up after previously working. Other boards...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
I have installed CMSIS according to this
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v14.1.0%2Fsdk_config.html
documentation. After...
Hi Team,
One of my application needs the UART driver in both Interrupt and DMA mode for more data bytes transfer. No need of timeout operation or polling mode.
Can any...
Hello Nordic;
I use SDK 17.0.2 and gls example . We know for security in pairing, considered a password which that is randomly generated in SoftDevice and sent to UART....
I am having problems loading an existing project that I successfully built and ran in the past.
I open IDE from nRF Connect > Toolchain Manager > Open IDE
The SES opens...
Hi,
Our Nordic app is doing BLE<->SPI communication.
All works fine when running in debug mode with SEGGER IDE.
Once we run without the debugger running, the SPI transmits...
Any idea why I need to send write enable twice, without reading the status in between, to get the write latch set?
It doesn't work this way, but if I change "#if 0"...
