I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I have purchased eval kit and entered bootloader mode by pressing BOOT/RESET button while powering up the device but haven't put any file but now when i power up the device...
Hi,
We are in a stage where we want to perform certification of a product and are now looking into an application that can be used to this end. The board is using SDK 15...
Hi,
I've bought a nRF52840-DK kit to evaluate a Nordic BLE SOC (we are interested in using the nRF52811). I've installed SEGGER Embedded Studio 4.52, and obtained a Nordic...
Hello, I am I'm a Beginner at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
I am developing using the example of 'ble_app_uart...
Hi everyone,
I am trying to understand the Memory layout of nRF52840 SOC in order to apply RAM retention into specific section. Looking the memory layout at pg 21 of the...
Hello Nordic community,
I have a nrf52-DK with SDK15.2.0 and I'm trying to communicate with ST HTS221 sensor. I have the original STEVAL-MKI141V2 evaluation board.
I...
Hello,
I was wondering what examples we have in nRF Connect SDK (NCS) for firmware updates over BLE and serial (receiving an image from another device over UART). Specifically...
Hi
I have bought NRF5340-PDK board to study BLE-MESH. I found that there is 2 development tool in Nordic website
1. nRF connect SDK
2. nRF connect for Desktop
...
Hi,
I have a custom PCB that uses the nRF9160 and an RGB LED. I want to drive this LED with PWM but it uses an active LOW style of GPIO drive. I have been able to use normal...
I'm using nRF52832 with SDK v15.3 and S332 v7.0.1.
The Wireshark capture snippet shows our product connected to an iPhone using our proprietary service with a single notification...
I am using the nRF SDK v15.3.0 example project ble_app_rscs on a PCA10040 development board. I am trying to determine the functionality I need to port to my pre-production...
I would like to get timestamps with ms accuracy in order to compare it with power measurements taken simultaneously. The +CCLK command accuracy is in seconds and there are...
Hello, I am currently working on a nr52840 s140 Sdk 17.0 (dev kit) and a m using the peripheral/uart example code.
The UART TX & RX works perfectly when connecting to a...
