Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hello,
I am using simple_adc__pca10028 from 8.0.0 SDK to read values from my sensor, its a kind of tensometer. My configurations are:
NRF_ADC_CONFIG_RES_10BIT...
Dear sir,
I am using your NRF24L01+ chipset with STM32F407ZET6 controller for 2.4GHZ RFID communication. can u please share the STACK for this controller.
I have a few questions (using nRF51 DK and/or external nRF51822)
I use an analog pin to measure the voltage of a capacitor of an analog circuit. From time to time...
Hello,
I would like to implement HID over GATT profile (BLE) in the Beaglebone Black (BBB). The BBB will be used to interface with a laptop/computer running Windows 10...
Sorry for this long message. I am new and quite lost.
I just purchased a nRF51 DK and installed nRFGo Studio, Keil MDK and NRF51 SDK. With nRFGo, I programmed the Segger...
Hi,
I'm trying to link the static esb library (esb_gcc.a) with the mbed toolchain. Everthing seems fine until the last stage of the linking phase where my actual functions...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
I have inserted the USB dongle nRF24LU1p in to PC. In nRFgo studio, it is detected as nRF24LU1+ Bootloader. If I click on the bootloader, It shows a window from where, it...
Hi,
I've got the following error when trying to update the softdevice and bootloader on my iPad:
Error on StartDFU Message:Data Size Exceeds
I've carried out the...
Hello!
Do I need any extra passives, connecting SD card to SPIM of nRF51?
It works fine with MOSI, MISO, SCK, SEL, VCC and GND directly connected, just want to be sure it...
Hello,
I am getting NRF_ERROR_NO_MEM when initializing second PWM instance, I tried to find the reason, but no luck. Please help.
I am using nRF51822 with SDK9 (+fixed...
I bought a EV board below to develop in the nRF51822
( www.wvshare.com/.../BLE400.htm)
I have installed all necessary tools like Keil MDK-ARM, J-Link, nRF51 SDK and nRFgo...
Hello Everyone ,
I am using ble stack S110 , BATTERY SERVICE , my CUSTOM SERVICE and pstorage module in my application and using SDK 7.0.0 and keil 5.12 IDE .whenever a server...
Hi
We are making a product based on nRF51822 and have used the ST BAL-NRF01D3 balun, but due to lack of updated datasheets for the balun we are unable to determine if it...
