Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi,
Currently I am sounding a simple beep on and off sound with a Piezo Buzzer on the nRF52832 and using the power profiler, it is consuming approx 713.323 μA, I was wondering...
Hello!
I have a question about the slave latency: I know how it should work, I would like to know if it is normal that there are current peaks in the supply current when...
Hi,
Does anyone have a hex code that can be added to the app hex in order to get rbp for NRF52832? Or a code that can be used from Arduino IDE?
I know that it can be...
Following error throwing while using nrf tools
nrfjprog verion 9.3.1 -------------------------------------------------------------------------------- FUNCTION: open_dll...
Can someone explain the indepth working of nrf dfu bootloader example with respect to the init packet.
How is it decoded and the information gets stored in the structure...
Hello,
I'm getting started using the nRF Sniffer with PCA10040 and Wireshark on MacOS. I followed the instructions in the User Guide and was finally able to set it up by...
Hi
This is just a head's up. In function nrf_esb_pop_tx(void) you have the following code ...
Instead it should be the following...
Otherwise the bug is such that...
The Introduction page is inconsistent:
infocenter.nordicsemi.com/index.jsp
first it says
[quote]]The mesh stack is also compatible with the nRF52810 platform, but not...
Hi all,
As I've been researching, the mesh sdk is not supported on the nRF52810 SoC, although being compatible. Is there any development or plan in changing this? I'm planning...
Hi,
Is there any way to add conditional compilation in linker file?
I have two versions of a code, one with DFU and one without, i want to combine the versions. is there...
Hi everyone,
I used SPI interface to access a external flash with page size 256 bytes.
I found I can't access full page, because the maximum of one SPI transaction is...
hello all ,
controller nrf51822
i am trying to development for EPD 7.5 spi interfacing through external flash image send so how to set spi latch reset turn on parameter...
Hi, there
I try to use the nrf_atfifo in my program, but I found the atfifo cause hard fault in my program,below is how I use the at_fifo in my program.
and I also found...
Hello, I have a problem with my nrf52832 customised board
It has loaded the ble_app_uart example of the 15.2_SDK and It have the correct pinout from my board, These are...
