I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello,
As mentioned title, when using printf with softdevice, "Stopped by a vector catch" occurred.
I am using my custom board(nRF51822 and s110).
And I am using IAR...
Hello,
When i try to set value of the gpregret using sd_power_gpregret_set and clear functions in on_write callback function, cpu gets stuck (i check it in debug mode). Can...
Hello
I'm trying to communicate with an sensor over the TWI HW interface during a BLE connection with the S110 soft-device, and every time I try to use the TWI bus the...
Greetings,
There is a bit of strange operation in UARTE peripheral in nrf52832 with the DK. In the simple code below, if both of the if statements with comments 'Check 1...
Hello everyone,
I have a strange issue with s110 + whitelisting + Device Manager + nrf51822 + GCC and hopefully you can help me with a good advice. It appears that the...
hi,
I am trying to integrate buttonless switch to boot loader as explained in the documentation and the hrs experimental example.
I am working on SDK7.2.0 and using...
Hello,
I installed the new nrfjprog but it fails to write my nrf51 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with
ERROR: argument...
Hi All,
I would like to design a wireless system using nRF51822 with an effective range >100m LoS and 5m under water.The system is used as a ON-OFF control device powered...
I am trying to run an Arduino sketch using the RedBearLab nRF51822. The sketch is designed to transfer data to and from a microprocessor and an Android device via bluetooth...
I'm currently want to use the NVM with ble device, when I tried to send values from the mobile app to be stored to the NVM, it doesn't work, I guessed that the problem that...
I want to write a device ID to the UICR registers at the same time as I flash the app code. I don't use Keil or that nrfproj.exe thing, I'm on a Mac. I have these targets...
Dear Nordic team,
I have the nRF51-Dongle and would like to use it with master control panel.
I did everything like already recommended in this tutorial .
The problem...
SDK 9.0
nRF51
PCA10028
I want use nRF51 gazell function one host multi device. Reference example code "gzp_dynamic_pairing",host and device can auto pairing .
But in host...
