after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Background : To set up a Matter ICD (Internet Connectivity Device) and Thread as a SSD (Sleepy End Device). Here are the detailed settings：
Currently, the Matter over...
I have v3.0.0 SDK currently . I am using nrf54L15DK . Do we have any sample code for checking AOA and AOD of the advertisements from the peripheral devices.
I could find...
Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
Hi Nordic
I’m working with the nRF5340 and nRF21540 for 802.15.4 and would like to know:
The expected RX sensitivity estimation for this combination.
Any reference...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hardware Setup:
Boar d: custom board using nrf5340dk_nrf5340_cpuapp
N CS Version: v3. 0.1 (upgrade d from v2. 4 where it was working)
Problem Description: After...
Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
I've recently tried to move from SDK version 2.6.3 to 2.9.1. However i've run into issues with this transistion.
I made a new custom board, by following the guide...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
