Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello,
i'm trying to use SPI with nrf9160DK as master and RFM96 module as slave. At the moment, i'm developing elementary functions to write and read from my slave device...
Hello
I am working on Nordic nrf52832
I am using the "ble_app_blinky_c_pca10040_s132"
I want to use ble for scanning a beacon (eddystone TLM) and collect its data. ...
please help. I need functional description of what is need step by step for doing a zigbee hardware device switch and management over bluetooth on the thingy52, i have all...
Hi Team,
We are using the NRF52840 with s140 Soft device for our BLE application.
While we are facing some issues while doing debugging.
1. We are getting Hard Fault...
Are there any issues of pairing a nRF52833 using OOB pairing with a IOS device? Is there a good example code I could start with?
Thank you very much.
All the best
P...
The system requirements: 50 identical nRF53-based devices (each with a sensor and an actuator), positioned within a 3x3 meter square should be connected to a single computer...
Edit : The code posted below works on the 96x96 3V(LS013B4DN04) variant of the display, I still have no idea why it doesn't work on LS044Q7DH01, but I'm guessing it doesnt...
Hello!
I have some devices with a custom built PCB on my desk, all of which have my own custom firmware on it.
Sadly the devices don't have access to the debug pins...
Hi Team,
May I know the functionality of the below mentioned signals:
MIPI RFFE interface pins: VIO, SCLK, SDATA. MAGPIO interface pins: MAGPIO0, MAGPIO1, MAGPIO2. ...
Hi,
I got a question on nRF52832 platform. When it is brand new (so without loading any of our FW) and powered through 3V3, it draws up to 4.6mA when powered. But we also...
Hello,
We have seen the below error,
NRF_ERROR_INVALID_ADDR If the EasyDMA is used and memory adress in not in RAM.
While trying to connect with an external sensor hub...
Timer A with a 10-minute interval, timer B with a 4-hour interval, and timer C with a 10-second interval are required, and A and B should also run out of time in low power...
Are there any updates on coded phy support for the nRF sniffer?
I found a thread about this from "over a year ago" which says to check back in 4-5 weeks: https://devzone...
When CENTRAL connects how can I read the UUID and ADDR of the peer?
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context) {
switch (p_ble_evt->header...
Hi Team,
We are facing issue with Flash storage Handlers with ble handlers. When we add the fstorage to my application ble adversing is stopped suddenly.
We are having...
