Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Dear Nordic Developer Zone,
I am using nRF51822 with softdevice.
I don't understand very well the advertising mode "whitelist".
My target is to be able to connect...
Hi all!
I'm running my code based on example "ble_app_template". When advertising without doing anything else, the current comsuption is about 200 uA.
Then I added a...
Hi,
i just started again working with nrf51822 but now with eclipse+gcc and with new soft device S130.
I am struggling with the addresses of flash and ram. I want to...
I have been working on porting my code from Keil to gcc because it has grown larger than the 32K limit that the free version of Keil allows. I am using the s110 softdevice...
Hello, I have a problem during first programing PCA10003 blinky_example. I get an error:"Flash Download failed - "Cortex-M0" "
Keil v4.74
SDK v6.0.0
In nRFgo Studio...
I've been trying to get the SDK softdevice ble demos to work on a mbed board. I'm using pyOCD+linux. I can compile and flash elf (.out) files in gdb with 'load' and I can...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
The nRF51822-EK, when powered over USB, seems to be working on 3.0V. The C232HM SPI cable is a 3.3V cable. The nRF51 data sheet specifies VIO as VDD+0.3 as absolute maximum...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi - I saw this post and I'm not sure how to add a clarifying question on to it:
devzone.nordicsemi.com/.../
We have a similar problem in that we built our boards with...
Hello,
I am working on an application that involves sampling audio data ~8KHz. I have a few questions
The real time clock module has a maximum interrupt frequency...
Hi everyone,
I bought two NRF24L01+ off ebay a couple of week ago and started to work on them this week. I seem to have problem with establishing a reliable communication...
Hi,
I use : An nRF51822 mbed kit + Kiel 5
So I updated the firmware like this : mbed.org/.../ and I dropped s110_nRF51822_v6.000 into MBED(H:)
I successfully use...
Hi,
i read about a new Chip revision of nrf51822. So i have to buy new Development Kit. How can i find out what it is the actual DK and where to buy it. I don't want to...
Hello All,
I was looking at the flash writewrite_example and the starting address is defines as:
addr = (uint32_t *)(pg_size * pg_num);
Later in the code, the example...
