I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to play the AT45 DataFlash driver by directly copying the sample code from nRF connect SDK v2.9.1 (C:\ncs\v2.9.1\zephyr\samples\drivers\spi_flash_at45...
Hello,
i have one PPK2. Recently i find the current reading from PPK2 is relatively large compared with actual current value.
For example, actual current value vs PPK2...
I am currently working on creating a custom PCB which features an nRF9151 module. I am currently working on pin assignment for our peripherals. Given Zephyr uses a device...
Hello, we're currently developing BLE devices with PCA10040 and nRF Conenct SDK 2.9.0.
During a series of experiments, we found that with the same hardware and the same...
In NRF5 SDK17.1, I disabled the Bluetooth broadcast channels 38 and 39 by configuring channel_mask. However, when I measured the broadcast current waveform, I found that there...
I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
Hi all,
lesson2, excercise2 is missing the code snippits.
Excercise1 and excercise3 do have code snippits to copy.
I tried on both Chrome as on Edge, but the snippits...
Hi,
I have successfully updated the firmware on the nRF5340DK controller using the DFU MCUBoot method. Now, I need to add Secure Boot NSIB to the bootloader and integrate...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
On the nRF5350 I'm currently seeing about 30 kB throughput via bt_l2cap_chan_send. It seems that could be optimized to over 100 kB. I'm looking at some values in the l2cap...
I am using zephyr_nanopb_sources to add some protobuf files to my app target, and this works fine in a normal build without mcuboot. However, when building with mcuboot it...
I am in the process of getting a Nordic Thingy 91 X up and running for an upcoming development project. However, I’m having some problems getting the Thingy to connect to...
Hi,
I started the LBS example on the nRF52DK_52832 kit and connected the PPK2 kit to the P22 pins for measuring power consumption. I am not sure if I did something wrong...
In the old Nordic SDK we had the option of using "high accuracy" interrupts with GPIOTE by using something like NRFX_GPIOTE_CONFIG_IN_SENSE_LOTOHI(true);
Is there a similar...
