Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am trying to do the dfu update in my custom flutter application like it does in the nrf connect application. My device is correctly being put in bootloader mode and the...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
I'm developing a small IoT device that needs to retrieve and transmit its location upon pressing a button. While testing the modem using AT commands, I can consistently retrieve...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
H ello Nordic team,
I'v found a bug on mqtt sample (using both ncs 3.0.0 and 2.6.1).
Description
Settings CONFIG_MQTT_SAMPLE_TRANSPORT_CLIENT_ID and trying to connect...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
Good day,
I am trying to program the nRF Sniiffer firmware to my nRF52840 dongle using the "nrfutil device program" command.
According to the User Guide v3.2 for the nRF...
Hello,
My new dev kit is not being detected by Windows Device Manager right out of the box. I've tried multiple USB cables and I've confirmed VBUS=5V is present on the input...
Hi,
Programmer can't read chip information after i download firmware with VSCode.
Before download, Programmer can read chip information.
Tool : Visual...
Hi all,
I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem.
The red area is the data I sent, but the blue area is not what I sent....
Hi everyone,
we are trying to use the TWI interface of the nRF52832 to communicate with a TI BQ28Z610 fuel gauge, using the TWI driver of the nRF5_SDK_13.0.
For the last...
This sounds like a stupid question... but I would like to clarify if this pin is an input or output. I think it's power in but want to make 100% sure as I'm spinning a PCB...
Hi , am working on nrf52840 .with nrf desktop v2.9.1 . I am working on display ST7789V with the nrf52840 using Zephyr. I have integrated overlay file . while working on it...
