Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
I need to put my external Flash into the deepest possible sleep mode possible,
I saw this api in flash.c in Zephyr, I am using the
( flash_ex_op ( const struct device...
Hi,
I am trying to integrate Buttonless DFU in my application. I have implemented all the steps mentioned in this tutorial.
Getting started with Nordic's Secure DFU...
I have 2 more questions still left for Channel Sounding:
1. I think i now fully understand how the filters work... But when i try this code, they won't connect:
2. I have...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
I'm currently using NCS 2.9.0.
However, the default certificate path is C:\ncs\v2.9.0\modules\lib\matter\credentials\development\attestation .
I used the parameters below...
Hi,
I have question about a project I'm running on nRF connect sdk 2.9.1.
I noticed that whenever an i2c sensor device device_init() is returning a value not equal...
I can't connect my newly purchased PPK2 to Power Profiler V4.2.1. The log shows: 2025-04-22T22:23:19.069Z DEBUG Sending event "ppk: running nrfutil device" 2025-04-22T22:23...
Hi Nordic Team,
I'm currently working on a BLE project using the nRF52840 DK with the nRF5 SDK (not using SoftDevice Controller), and I’ve run into a critical issue related...
I want to build the sample usb_hci.
After i create a build config there are warning and the process fails
warning: <choice BT_HCI_BUS_TYPE> (defined at boards/arm/ubx_evknorab10_nrf5340...
I am trying to scan for sensors on an I2C bus using the nrf54L15 and Zephyr RTOS. I modified the i2c example from here: https://github.com/iFransL/i2c-scanner/tree/main
...
Hi,
I'm working on an application where the system should enter System OFF mode after some button activity and wake up (restart) on a button press or USB connection.
When...
Hello,
I’m trying to understand exactly how the location module works in the Assert Tracker V2 application. I want to see the NMEA data in the logs, but I’m not sure how...
Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development on NCS2.9.0, and we meet some problems:
1. when the matter.ota is 1003KB, takes about...
im trying to develop a prototype that uses a thingy53 and lvgl to draw a screen on a solomon ssd1306 attached via i2c (kwiic) but am having issues with getting it to build...
