But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi Team,
In current application, each BLE node (nRF51x22) need to switch between Broadcaster and observer roles . Beacon kind of behavior is required i.e. no connection...
Hi All,
Please, I have some questions about the use of iPhone wireless shutter release button:
Q1: Is it possible to connect to an iPhone wireless shutter release button...
Open the nRFgo Studio and connect PCA10028 (NRF 51DK Board) then Erase all data
Open the uVision V5.18a
Open the DTM project file of the example in the following...
Refer to the NRF 51DK Spec page, It can be support Bluetooth 4.2 spec.
In the Bluetooth 4.2 spec, The device can support the maximum PDU size of 255 bytes
Where can I...
Hi Everyone,
I face a problem regarding uploading Application Hex file, I use nRF Toolbox v 1.15.0 mobile app to upload the firmware, Bootloader is successfully uploaded...
Helo, i'm working on firmware for a device, which should be able to scan for other devices, advertise data and be connectable. Scanning and advertising works. Problems come...
Hi All,
Am using NRF52 ,S132 soft device , I am trying to send two packet of twenty byte every 5s . in a timer interrupt handler I call ble_nus_string_send twice continuosly...
I have following set up for current measurement.
NRF52 DK PCA10040 v0.9.0
nRF5 SDK v11.0.0 : Power Profiling Application
S132 SoftDevice v2.0.0
nFR Master Control...
hi
does my nrf51422 v2 have uart over ble?
its version 2 and its supported sdk is 6 and it does not have ble_nus.c
does my nr51422 v2 support uart over ble?
Hello,
I've been playing with BLE applications with my custom board with nRF52832.
I have flashed "flash_s132_nrf52_2.0.0-7.alpha_softdevice" from ble_app_template project...
Hi
I'm having issues implementing ADC sampling to my ble project.
I'm using the nRF51-DK with SDK11 and S130. I used the example from github ( github.com/.../adc-example...
I want to update over BLE with using DFU tool. But do not start updating process.
DFU tool indicates "Enabling DFU Bootloader".
Bootloader stops at memcpy() of dfu_ble_peer_data_set...
Hi there,
I am now in FCC stage and finalizing a FCC code using the radio test sample code. I do have a delimma on what type of radio mode I have to use. Will you please...
Hi,
I am working on a school project, and I need to use a nRF51 dongle as a BLE master. However, when I try to use JLinkExe to connect to the dongle, it fails all the time...
Hi am using NRF52 board ...and am trying to send data(which is not a string) using ble_bus_string_send . I send data only once from a one second timer but the other side is...
