Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
It is unclear for me why the following code look like this (conn_ble_gap_sec_keys.c, SDK15):
Is it logical that here the SER_MAX_ADV_DATA is used? is there actual advertising...
Hi , nrf connect V.2.5.0 in windows 10 64bit, fails to launch Bluetooth low energy app. "DEBUG UART read operation on port aborted" is the log info which i came to know from...
Hi,
I have a BLE sensor node (firmware not modifiable) that takes up a peripheral role and starts advertising when powered up. Typically, one can scan for the node from...
Hi All!
I have been working on bringing-up a custom manufactured nRF52832 board. I have with me 6 boards, the first 3 are working fine, the other 3 are not. In both cases...
Hello all,
I'm practicing creating my own service following instruction from this link: https://github.com/bjornspockeli/custom_ble_service_example
Now I stuck at part...
Hi everyone,
I have configured two UARTES , one using the app_uart library and another using nrf_serial library.
I am using SDK15.0 alongwith s140 softdevice with bluetooth...
Hi There,
What are the difference between system off, ram retention, RTC wakeup vs system on with ram retention, RTC wakeup vs FreeRTOS tickless with RTC wakeup? And what...
Hi team,
I noticed a very interesting incorrect pin description in the latest product specification of v1.2 for nRF52810, QFN32.
Above picture shows we have 2 p0...
I'm using the PCA10056 with an SD card connected via P1.12-P1.15. When I use the FatFs example of SDK12 PCA10028 it works fine. but when I use the FatFs example of SDK15.0...
Hello,
I've got the nrF52840 and would like to create a simple application to send temperature to my laptop. Then the next step would be to create some mesh network with...
Hello,
I am working on Custom BLE HID Keyboard. I am currently trying to understand working of program given by nordic in SDK-10.0.0. THere is one problem which I am facing...
Hi,
I've tried to implement the DFU_buttonless example to my development board. I programmed the bootloader and the settings-page. The bootloader detects the application...
I'm currently in the prototyping phase of getting two nDK52840 boards talking to each other. I currently have one board flashed with the central role, and another board flashed...
Hello.
What do I need to run this example called uart?
As far as I understand this should be simple echo program meaning what comes in goes out but I can not see anything...
