dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I am using sdk12.2 and customised nrf52 board.
I want to interface ultrasonic sensor with nrf52. In this I am enabling trigger pin as high and after sometime my...
Dear All,
I am working with SDK version 15 and softdevice 132.
I want the device to advertise for 1 minute. Then go to low power mode. Again wake up after 5 minutes...
I have twe NRF24L01 module,one set Tx mode with autoask,and another set Rx mode without autoask,
The channel and address are same.
Can I use this mode to communication...
I have problem flashing main program and SoftDevice on the nrf 51822 module. I have Keil version 5.24 and I am using SDK v12.3 .
I can flash SoftDevice easily but after...
Hi,
I init the UART pin with the AIN pin such as P0.05, but the program will run into __WEAK void app_error_fault_handler(uint32_t id, uint32_t pc, uint32_t info) every...
Hi Everyone
I have been trying to do some simple led blinking by generating events , however i need to do that if a button_0 is pressed for some duration.
Here is a code...
We are using SDK 15.0 and Softdevice 6.0, FreeRTOS 8.2.1
Is there a way to use softdevice and NRF_SDH_DISPATCH_MODEL_INTERRUPT?
If not, it means SDH task MUST be the highest...
Dear Sir,
I am using SDK15 and sodtdevice S132. I am testing on the kit BMD300.
I am using nRFConnect App in andoird to connect to the device and check the services...
Dear all,
I used SDK 12.3 buttonless functoin with PCA10028(nRF51422), and I occur some problem.
I did some testing as below:
case 1. softdevice+bootloader
case 2...
hi Nordic ,
I am developing an USB product with the nRF52840.
Can you can request the use of Nordic’s vendor ID in conjunction with an assigned unique Product ID?
Or...
Hi！
I read datasheet: nRF52840 Objective Product Specification v0.5. It says 52840. When SPI is master, it supports 32MSPI.
Which of the following examples can I refer...
Hey!
I'm migrating from Keil to Segger SES, is there any way to get a similar checkbox interface for sdk_config.h in SES like the configuration wizard in Keil?
Cheers...
I am a newbie to BLE and starting with nordic ble chip. I downloaded SDK 15.0.1, is there any proper document explaining SDK directory structure. Thanks
Hello,
We have received in april 2018 nRF52840 QFN packages nRF52840-QIAA-R marked as well QIAA-R-SAM.
We would like to know to which version they are related : A, B,...
Hi. Does anyone know where I can download the CDC ACM diver for windows 7?
I am running the example on the nRF52 dev kit, but I get an error as windows can't find the driver...
