But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
nRF52810 only supports S112 so the max throughtput anyone can achieve is 330 kbps .. please provide proof.. test data. Only nordic employee please answer this or someone who...
In SDK 15 the bootloader DFU enter check in nrf_bootloader.c has the following code:
if (NRF_BL_DFU_ENTER_METHOD_GPREGRET && (nrf_power_gpregret_get() & BOOTLOADER_DFU_START...
Hello,
We are working with Low Energy sensors that are programmed to make a periodic ADVs to our scanners/apps/Raspberries, in order to start a service if required. So the...
Hi,
I am using cli and made my own command like bellow, as you see i have a command with 3 sub commands. But i think my idea is primitive because if i have 1000 sub command...
I am starting building industrial-grade system which contains several nodes connected via wireless channel.
As a wireless protocol I decided to use BLE 5 due to long ranges...
I am trying to program mpu_simple https://github.com/Martinsbl/nrf5-mpu-examples with Segger, and I get to connect sensor MPU6050 to my board but I do not receive datas of...
Hello. I followed all the steps provided in the readme document. After dragging and dropping the hex file to the j link, the led 1 starts to blink, indicating that the board...
With an nRF52, is it possible to wait longer to measure the RSSI on a channel? I'd like to measure the RSSI over 1msec or so, rather than a tiny 8us (typical) snapshot.
Hi,
This is my first time to use Nordic product and I have used nRF52832 based SDK 12.0 and SoftDevice132 v2.0 about 2 months. And the IDE used for devlopment is KEIL MDK...
Hi
Im using the DFU secure example (examples\dfu\bootloader_secure\pca10028)
Im working on a NRF51822-QFAA ,S130 SDK12.3 , Im not sure about my IROM/IRAM definitions,...
Hi Nordic Team, One of our customer wants to integrate communication via Thread BLE on his IoT-Gateway. We found your nRF52840 Dongle. Does this dongle have any certifications...
Hi,
I am planning on using nrf52832 for a beacon application. I happen to get a schematic and layout from Nordic website for development.
I am attaching the schematic...
Hi, I am trying to interface MPU^)%) sensor with NRF52832. with help of BLE UART. i will get the resultant data on BLE APP. but here i got some error is this the linking error...
Hi,
we want to made the device which should working in the mesh network without provisiong procedure by user.
Typical application - network with 500 nodes, every node...
