I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi, probably a simple answer to this but am struggling to find a decent answer on the web.
There is a function (below) and I would like to watch the p_adv_report. However...
BACKGROUND:
So I've got minimal experience with low-level development/low-level coding/digital hardware, being more of an antennas person before, but have been given a task...
Hi All.
I am using the nRF52840 development board, and can't get UART logging to work. I have checked all the settings in sdk_config with no joy.
I have hyperterminal...
Hi Nordic:
I'd like to ask a mesh specification question, there is some terms relative to retransmit: "4.2.2.6 publish retransmit count", "4.2.19.1 network transmit count...
Hi,
Development Environment : Windows 7 and keil MDK- ARM 5 and nRF81522 EVK
I want to know that which SDK version should I use and I am using Arm debugger programmer...
I would like to know if I can run Thread examples on nRF52840 USB dongle? Could someone provide instruction how to do this in a Windows environment?
Also, is there external...
Hello,
I'm trying to lower the power consumption in the s.c. "System ON" mode. I need to run in System ON mode to keep the RTC running. However I need to wake the CPU on...
hi ,
I use SR3 V1.2 to test. I enable ANR, play the recording directly in the loop.
About every five seconds, a second or so of unusual sound appears. The rest of the...
Hi,
I can't understand what is DFU example inside /examples/dfu folder and what is /bin/bootloader/? I read DFU quick start guide, but where is source code of bootloader...
I try debug my app in keil debugger but it's often raised app: SOFTDEVICE: ASSERTION FAILED in SEGGER after step down through the code (in few steps).
My app based on buttonless_dfu...
Hi,
I have a doubt regarding buffer setting in SPIS.
In the SDK15 SPIS example, buffers are set using nrfx_spis_buffers_set(...) and it works perfectly.
I was wondering...
Hi All,
I am using nrf mesh SDK v2.2.0 and nrf SDK v15.0.0.
I have created a new model in nrf mesh SDK, this model is publishing scanned data on group address.
When...
Hi,
I was working on the HID mouse example and noticed that the example gets disconnected from my mobile phone once i start moving the cursor.
I also noticed that the...
Hello,
I am performing current measurements on custom hardware with the nRF52840 and comparing my results with the values in the nRF52840 product specification. I noticed...
