Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi All,
I am trying to understand the possibility of using Bluetooth Mesh technology for voice communication for longer distances.
My main problem is to communicate longer...
Hi,
I was wondering if it was possible to notify the application layer if the central device is scanning and it (the central device) sends a scan request to an advertising...
Hi,
I have two questions regarding the UART and SPI communication at high speed.
I am using the UART and SPI to transfer data on nRF52832 and sdk 17.0. I connected an...
Hi Team,
I try to design a PCB based on nrf52840 chips, can you help me check if it is right?
Something like Power supplement, SPI interfaces, and debug and programming...
Hello,
I am currently using nRF Connect SDK v1.7.1 with a nrf9160DK. I keep getting "create_nordic_project.py filed (1)" when I try to open a new project with a overlay...
Hi, I am trying to measure power consumption (the device is an nRF52840 dongle) and I get different results when the board is connected or not to a JLink external debugger...
HI
I need to port my application from NCS v1.5.0 to NCS v1.7.1 Here, I have already tried to transfer my ble application to a higher version. I can't able to do pristine...
@Nordic Semiconductor General Chip nRF9160 rev2 Voltage 3.7 PSM Periodic TAU 5.0 hours Periodic TAU timer element "00011110" Active time timer element "00000000" RRC connected...
Hello,
I have implemented a somewhat working RX algorithm for receiving data over UART but I'm looking for a good way to make it more robust. I haven't found any good answers...
Hello,
I'm try to follow the instructions for multi image example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html#ug-nrf5340-ses-multi...
Hello
I have 2 custom boards both with nRF82532. One is central and the other a peripheral. I use LESC. When no bonding information is stored in either of the devices, pairing...
Hello,
I am using mfw1.3.0 and NCS 1.7.0 developing an application on a custom board implementing the NRF9160 and NRF52820 (The 52820 is put into very low power using nrf_pwr_mgmt_shutdown...
Dear Nordic,
we need to save few bites (product serial number, few settings). we use BLE with bonding on a FreeRTOS based FW. PM is already using FDS, at it is not clear...
