I am try to make Bluetooth LE with Nordic UART Service bondable in to pair with central, not requiring to enter pairing code again and again.
I have set followings in prj...
Hi,
I am using nrf52840 to run as an hci controller over UART for nrf91. I was able to implement FOTA over BLE for nrf91, but I would also like to add an option to add FOTA...
Hello, After a lot of struggle i was finally made it to the point i can build and flash to my thingy 91 the lte_ble_gateway. However, i added prints (printk) in main.c to...
Hi everybody I'm using nRF Connect SDK 2.6.1. Before I could seen Partitions section in Memory Report tool, but now it's disappeared. I also checked it by ninja command: ...
I work samples/bluetooth/scan_adv on nRF54L15-DK.
Disable LOG and CONSOLE.
I measured current comsumption by PPK2.
Result is about 4mA.
On datasheet, nRF54L15's Bluetooth...
Hi,
I've received the nRF54L15 DevKit and tested the power consumption during sleep Testproject in GIT: https://github.com/marcel-cd/nrf54l15dk-powertest
The result was...
After some time I picked up my NRF5340 DK again to continue my Matter samples. But I noticed I cannot program any sample to it. The Segger seems to work fine, as I'm able...
Hi,
I would like to use hal_time_get() [hal_timer.h] in my project, and I try to add below library into Makefile.
but I got an error. "error: implicit declaration of function...
i am using/ ble_app_multilink/ example present in central folder..i am beginner to this ,,so i have few doubts in it
1)so where actually advertisers(which are advertising...
Hi,I had a problem with nRF51822 DFU.I tried to OTD nRF51822( version SDK_9.0.0 s110 ) wiht Android 9.0 devices( nRF tool version 1.9.0 ),but it always fail at 1%.The problem...
Hello fellow Nordic-ians,
I am developing a custom firmware for Nordic Thingy 52. I am using the Segger Embedded Studio as my IDE and J-link Edu Mini as the programmer ...
Hi,
I have found zboss 1.0 opensource.
Surveying the source, i have noticed that variable "g_zb" (nicknamed by ZG) give system informations.
I can find zed address(16bit...
Hi,
Here is my setup, NRF52832 PCA10040 s132, sdk 13.0.0.
I work on Windows 10 with a server (The aim is to do it from a Raspberry later) which one is connected to my...
Hi,
I'm developing a simple sensor application using s132 on NRF52832_XXAA. The application works fine, except that I have problems disabling the saadc module after conversion...
Hi, How can I configure so that I can transmit real GPS data of the device and watch it from nrfcloud? I think I need to change something in config files? Simulated GPS data...
Hello,
in the ble_advertising_start() function of SDK15 I noticed, that the check for the secondary_phy is the same as for the primary_phy.
I assume this is a copy paste...
Hi.
I am trying to choose the crystal and external capacitor for nRF51822-QFAA-LDO. I found the crystal with load capacitance 10pF. As mentioned in reference paper,
...
Hello. I am having problems when I connect one of my PCA10056 boards (nRF52840-DK) to my Windows machine and run nRF Connect v3.0, Bluetooth LE app v2.3.0. When I select the...
Dear Friend,
Using this tutorial I imported a Blank Blinky Kiel Project of SDK 12.30.
I am using a custom board with nrf51822, I imported the PCA100028 version.
...
Hi,
i am working on power management for nrf52832. i used icm20948 for gyro and accelerometer. my battery capacity is less. so when my mcu is going to sleep but gyro and...
Hi,
What is recommended to do for update SEGGER Embedded Studio for ARM 4.12 to newer version?
Is there any update tab from SEGGER or I need to download and install from...
Hi all! We have to work with PPK and nRF52 DK. For a measurement was used Power Profiler application from nRF Connect tool.
Is it possible to do the measurement in interactive...
