Hello, I've a nRF9161DK board and I would like to connect a UART to an external device.
Looking at the schematics I see that both UART0 and UART1 of nRF9161 are connected...
toochain：3.0.2 sdk3.0.2 nrf connect Every time I build, it gets stuck here: Found assembler: C:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi...
Hello, I know it's a bit basic, but running through all the docs for thingy91:x I got a bit lost.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/device_guides...
Hello, I am the hardware researcher currently evaluating this product.
I am currently working with the nRF54L15 DK and have encountered an issue where my application appears...
Hi Nordic team,
I'm currently working on a real-time distance measurement project using channel sounding with the nRF54L15 DKs. I’ve been using the channel_sounding_ras_initiator...
Man,do you have the experience on DIY Bluetooth headset with PCA100059?
I raise this question for I hate the current product limit: limited time to run,short lifetime of...
Hello, I'm trying to perform a firmware update using the FOTA feature on the nRF7002. After building and running the firmware update code, the following error occurs:
...
Hi Sir,
I am use S132 softdevice and it converted to binary file using srecord tool, the add binary file into IAR project seems not working for softdevice.
Below is my...
Hi! I'm brand new to Nordic development. I am unable to get blinky working for the nrf52810 SoC, running off of the Rigado BMD-330 evaluation board; however, I am able to...
I'm having what I believe is a hardware problem on a custom board with an NRF52832. Unfortunately I cannot share the schematic, but will try to describe the symptoms and will...
Hello,
I also think my question seems wired, but I have a situation to make same production of 2 type about BT exist.
I will use 3rd party BT module when BT type product...
Hi all,
I have a problem where I get a Flash page erase failure when scanning interval/window is 3.125 ms (or other very small value).
(SD132 2.0.0, SDK 11.0.0)
When...
Hello,
I am currently working on a custom nRF52840 board. I have to make the nRF52 communicate with a chip using TWI, so I started from SDK 15.2.0 TWI Scanner example...
Hi!
I try to compile secure DFU from examples SDK15.3 for nrf52810 (pca10040e_ble). I added old files from DFU SDK15.0 in to my new project. Also added file micro_ecc_lib_nrf52...
Hello ,
I saw some examples in nordic forum in that they measured coin cell battery voltage level
how to interface 22v battery to nrf52832?
Thanks
learn
hello everyone,
In my application single central(ble_app_uart_c) scanning and check each peripheral(ble_app_uart) Mac id. which peripheral mac id is defined by central,...
Hi all,
Can anyone suggest me how can I flash raytech dongle nrf52840 ? I tried two following solution
1) I tried using SWI interface with dk board ,getting an error message...
Hello,
I'm having difficulty with an app which combines USB (CDC ACM) and 802.15.4 using Softdevice (15.3). The issue appears to be related to hfclk, which is started to...
I am using the Nordic SDK 15.3 for nrf52832 development board. I am using SES as my development environment but I am unable to get RTT logging to work.
I have enabled RTT...
I am using SPIM3 to drive a peripheral, only using tx. And I noticed that SPI is sending wrong/corrupt bytes once in a while. See below image where the code tries to send...
I am developing a multi-peripheral product that knows all the possible connectable central Bluetooth device addresses (centrals are all NFC enabled smartphones).
When a...
I am using QSPI of nRF52480 with freqency 2M Hz. Now I want to reduce to 1M Hz,
but QSPI_CONFIG_FREQUENCY min value is 15
// <o> QSPI_CONFIG_FREQUENCY - Frequency divider...
