Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Hi,
I have the following version(s):
Windows ver: 23H2 build 22631.4317
WSL version: 2.2.4.0 (OS Ubuntu-22.04)
VSCode Version: 1.94.2 (user setup) (latest)
nRF...
Hello I am using a custom board, based on nRF9160. I'm using SDK 2.7.0 and modem firmware 1.3.6. After a bug in production where a device stopped sending data, I tracked down...
Hello Nordic Team, I'm developing an project using VS Code with nRF Connect Extension for an nRF52832 board. The SDK version I use is 2.7.0 , build system is sysbuild . I...
I tried to claim the "additional 45 MB" for the Wireless Logic SIM included in the Thingy:91X delivery.
Unfortunately, the "claim code" seems to be only available via the...
In my project I have a BME280 that starts OFF, and I interface with SPI.
The system then turns the power supply and the bme280 is powered.
At this stage the bme280 needs...
Hi, Im developing NRF52 DK. I'm building library C SPI mfrc522 for NRF52. I'm implement PCD_Read and write PCD_register look OK, But i call function PICC_IsNewCardPresent...
Hi there
I'm using a nRF5340 (DK or ADK) with the Zephyr HCI UART sample from NCS v2.9 and the SoftDevice to stream music to two headsets (1 CIG with two CIS) from our stack...
I change name by app, after get new name from my app,save it to flash, then I call gap_params_init, in this function, I reload the new name from flash and set it by sd_ble_gap_device_name_set...
Hello Nordic Community,
I’m encountering an intermittent issue with my BLE peripherals, which are based on nRF5340 + nRF7002 SoC , while testing with nRF Connect Mobile...
Hi,
We are in process of performing CE Certification on a product with the nRF9160 module mounted.
The lab wants to perform conducted testing on the module with the antenna...
hey there, i have a project which uses nrf9151 with a pressures sensor from BOSCH which uses SENT protocol to transfer data, my question is 1. Is it possible to configure...
Hello, I'm using the nrf52DK for the chip nrf52832 with nrf connect SDK v2.6.1
I want to implement an advertising timeout say 5 minutes. How can I achieve that? any example...
I'm attempting to troubleshoot a system crash when polling a sensor at higher ODRs while BLE is enabled. I'm using NCS v2.9.0 with the nRF54L15. I checked the thread stack...
I'm trying to compile the lsm6dso example for a nrf5340. I also tried the nrf52832, but I get the same error.
v2.4.2\zephyr\samples\sensor\lsm6dso
prj.conf:
CONFIG_STDOUT_CONSOLE...
