Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi, I am conducting range testing with two nRF54L15 pdks using the Extended Advertiser and Extended Scanner sample code. One as an Advertiser and the other as a Scanner. ...
Respected Sir/Ma'am,
I am developing my Final Year Project using nrf52840 dongle, without DK. For programming, I am using NrfConnect for Desktop. I was testing different...
I am using all of the latest software/firmware as of the date of this message.
Lesson tells me to follow a link to "flash" the Thingy:53. Got to the point where the following...
Hello Team,
We need to help our client’s Matter over Thread product quickly pass the Matter certification test. What should we do to expedite the process? Do we first need...
NCS 2.4.1 nRF52840
My project is a battery powered SED based on the coap_client example. It is configured to autojoin using a hard coded pksd. I see on Wireshark that my...
Hello, I want to configure the BMP390 using I2C on my custom board. However, when I try to read the CHIP_ID register, I am unable to get the default value, and the function...
Hi,
I referred to this doc for hardware setup
However, in the programmer in nRF Desktop, I got the following log:
17:37:36.199
Error: Failed with exit code 1...
Hello person in charging,
I would like to know whether there are something information on vulnerabilities in the proprietary mode of nRF51 and nRF52, respectively.
Thanks...
Hello,
After an update to the NRF connect for Desktop the Programmer application can no longer program my nRF52840 dev kit (PCA10056, 3.0.0). Trying to revert the update...
Hi,
In our project, we're using Mcumgr FS to download files from our device.
After tweaking the BLE configuration parameters using the throughput sample ( https://github...
Hi
The datasheet of the nRF9151 is missing the statement in the nRF9161 datasheet:
RF 3GPP compliancy requires 3.3 V.
Is the nRF9151 reaching compatibility down to 3V...
I have four of these devices. nRF5340 Audio DK.
I would like to use them as follows. Is there a way to set them up?
Device A: source
Device B: sink left
Device C:...
Recently, we started developing our new project using the nRF52832 as our controller.
We are using Segger Embedded Studio (5.42a) as our IDE.
My question is: Are there...
