I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
My board (nrf52840 sense) has flash memory P25Q16H . When I put everything off, the board consumes 25uA. To save the last bit of current I would like to put the flash memory...
Hi,
I'm trying to remove the bonding (pairing) using the existing function ( delete_bonds() ) in the " ble_app_hids_keyboard " Sample Application from the SDK " nRF5_SDK_17...
Hello
I'm configuring Ping with AT command using API - nrf9160DK, zephyrOS. However, it doesn't go well. API reply "ERROR".
some other AT command goes well, but, Ping...
Hi, I am using the nRF52840 dongle + nRF Connect for Desktop App, and I would like to configure the data rate for packet advertising. Is this possible? Which one is set by...
I would like to use the cURL libary that is included in the nRF Connect SDK (v2.6.1) a nrf/ext/curl
I started with the download sample (nrf/samples/net/download)
I've...
Hello,
I am using matter SDK v2.7.0, when I run command below:
west zap-generate -z ~/Work/matter/light_switch/src/light_switch.zap -m /opt/nordic/ncs/v2.7.0
I get...
Hello, I designed custom board using nRF52832. But dfu is not working on that board. All other code is working fine. I am attaching schematic file of nordic part for reference...
Hi,
To prepare our new device, we are using a nrf5340dk board.
For our application, we need to perform DFU over BT.
Si, i following the tutorial https://academy.nordicsemi...
Hi,
we have been trying to implement modem delta updates to our nrf9160 project using DFU target. We send delta .bin file over LTE to our device, and save it to external...
Hi,
I want nRF91 to download the nrf52840 firmware update image from nrf cloud and then pass it to nRF52 using SMP over UART.
1.How can I use the nrf cloud FOTA UI...
When I program an interrupt, the NRF52840 requires 250uA extra. I read something about the sense interrupt, but I cannot find any working example. How should I implement an...
Hi,
I am working with Thingy53 using the ESB (Enhanced ShockBurst) library. I have my basic app running with multi-point comms and power control. This was done without using...
Hello,
We have a product which is a custom nRF52832 board, nRF5 SDK (didn't have time to upgrade to nRF Connect SDK), s132, BLE.
We used to call delete_bonds() function...
I‘m tring to run nRF5340 Audio applications with two nRF5340 Audio boards, following at: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.0/nrf/applications/nrf5340_audio...
