Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hello there. I'm currently looking at the sniffer software
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth-LE/Download?lang=en#infotabs ...
Hi,
I'm using nrf52840 and connect to a PC with BLE, using Nordic Uart Service (Rx and Tx characteristics).
When sending messages, I need to know how much data I'm writing...
Morning,
We have a technical question please. As far as we know the NB-IOT services in Germany should use only Band 20 for operation, but we see in our lab tests that some...
Hi
1、The customer wants to set read protection during batch programming，Customers use offline programming during mass production；
2、In addition to using nRFgo Studio to...
Hello.
I know that I can change the interval of the advertize event by changing the advertize interval, but I don't know how to set the interval to be sent to each channel...
Hi, We did design our own board/pcb using the nrf9160, but we have a problem to connect to network/lte. I did some debugging and I found out that when the method lte_lc_init_and_connect...
Can you please tell us what is the power consumption in Idle State with DRX = 1.28s and Sleep State with DRX = 1.28s? And an estimate with eDRX at 5.12 s? We are asking because...
Hello, I am using nRF52832 dev kit. I am trying to get lower current consumption. I used ble_app_blinky example and disabled the NRF_LOG. My settings are below:
Role: Advertising...
Hi, I used my NRF52840-DK for few times but suddenly the jlink connection was not detectable. Before the Jlink failed, the main controller on board did not bring up the board...
Hello,
I Cant upload BLE Code on nRF52832 breakout board from nrf52 Dk using Segger studio. Other codes such as blink are uploaded successfully. But there is problem for...
Hi,
I am trying to use radio notifications (mpsl_radio_notification.h) to call notify with data just before central connects. I do this with no problem with NRF52840.
...
Hi everyone. I just bought the nrf52832 Develop Kit. However, after trying to flash write the sample, my nrf52832 Develop Kit doesn't work and won't flash write the next time...
Hi, I'm using BC805M module which uses nRF52805 SoC.
I have a power ON/OFF button on the PCB. If I press the button (deep sleep mode) during BLE connection, the BLE will...
Hi, I'm using nRF52805.
In my code, I used BLE to transmit I2C and ADC data to the mobile app nRF Connect correctly and continuously.
I tried to use NRF_LOG_INFO() and...
