Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
when i connect NRF9160-DK (version 0.8.5 )to the CMW500 for CAT-M test, we have send the below three commands
AT+CFUN=4 AT%XSYSTEMMODE=1,0,0,0 AT+CFUN=1 to
the NFR9160...
Hello, all.
I'm using nRF52833, pca10100.
What I'm trying to do is just manually disconnect.
So, I referred to the Multi-link Central example. Multi-link Central is...
At this link https://infocenter.nordicsemi.com/pdf/nRF52840_Rev_2_Errata_v1.4.pdf, in 193 and 198 ID，this seems to be a mutually exclusive. In 198 workaround, .synchronize...
In the AGPS sample for nRF9160 "v1.5.1\nrf\samples\nrf9160\agps" main.c, there is option to set interval an and timeout in "gps_config" structure in "gps_start_work_fn" routine...
We ran into an issue when trying to use mcuboot on nRF53 with an external QSPI flash. In hal_nordic/nrfx/drivers/src/nrfx_qspi.c, the function nrfx_qspi_write has the following...
dear all：
I want to know how many beacons can be scanned by a gateway in the application of beacons.
At present, we have only actually tested more than 100 tags that scan...
Hi, Nordic Team. I'm using BC805M EK (nRF52805). In my code, I'm using SAADC (PPI interruption), TWI, BLE and System ON/OFF button .
Q1) I don't need RTS, CTS on the UART...
Hi
How to control two channels separately with one PWM instance?
I want to turn on/off the PWM output of each channel with any interrupt process.
app_pwm_disable() and...
Hi,
I am using nRF52840 , SDK 17.0.2/ble_peripheral. I am integrating Mesh SDK 5.0.0 libraries with ble_peripheral libraries in the nRF SDK 17.0.2 as per the documentation...
I created my first nRF52832 custom PCB board and I am having issues with poor RF performance. My project uses RSSI to estimate the distance between a peripheral and a central...
1.For example ,i have provisioned a few ble devices and added to the network by using an android phone .
Is it possible to do the provisioning with other android mobile...
Hi
I am using fds to store log in flash, after reading all data from flash, I am deleting record from flash.
But I found that Record ID incrementing from previous Record...
Hello,
I am creating my first bluetooth application and am having difficulties figuring out the interrupts. The application is working and is very simple - please see pseudo...
Hi everyone,
I have a fairly simple use for ADC: sample 4 channels (scan mode) every 10ms and store in RAM.
Every now and then (asynchronously) there will be a function...
