Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
I am using nrf52840 to run as an hci controller over UART for nrf91. I was able to implement FOTA over BLE for nrf91, but I would also like to add an option to add FOTA...
Hello,
I'm trying to configure the GPIO pins on the MDBT42Q-P192KV2 module, but they are not responding as expected.
I'm using the nRF52840 Development Kit to flash the...
Hi,
The errors that need to be resolved are as follows, and I think the sdk is not installed properly:
1.Please help me troubleshoot the installation problem of nRF...
nrf5340_audio application ， unicast_audio and broadcast_audio samples in zephyr， Are these all LE_2M by default ?
If I want to use LE_1M, how to change ? Modify prj.conf...
Action for Loading configuration is bugged. It Exports .overlay file but when Loading it only accepts .json file and it doesn't allow you to change it. Therefore, the file...
Hi I have recently bought the product nrf52840 from Digi key, i have dumped the code so many times but now days it is showing the error. the issues is whenever iam trying...
I'm using UART peripheral sample on an nRF52840 and SDK ncs v2.4.2. The Nordic module switches on another device (called UUT) which connects to its Rx and Tx pins.
I discovered...
Hi,
I am new to BLE development. I am using Visual Studio Code and Nordic SDK v2.7.0. I had working code a few weeks ago. I went on vacation, and when I returned I had all...
We are developing on the nRF52 Development Kit (nRF52 DK) for the nRF52832 SoC. Our application involves a 4-wire pipelined SPI communication with the Intan RHS2116 chip....
Hello,
I am encountering difficulties connecting to and recovering my nRF52840 board with J-Link on macOS, both via nRF Connect and using nrfjprog in the terminal. Below...
Hello,
We are using the nRF52840 dongle (PCA10059) with the CLI agent software as a Zigbee network coordinator, and the Digi's XBEE S2C as a Router.
We are using XCTU...
Hi Team,
I have nRF5340 DK board and I want to test the Bluetooth Periodic Advertising with Response and Bluetooth Periodic Advertising with Responses Synchronization...
Hi,
I am trying to create a new custom service in nRF Connect for desktop and play around with its characteristic properties.
I Use an nRF52840 DK as peripheral and my...
Hi,
Its maybe a stupid question but is there a easy way to operate the DK with 3V VDD and IO Voltage? The 9160 DK had a simple switch for this. The default for the 9151...
