Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I am using version S140 of an nRF52840 in an application that creates an extended (S=8) advertising beacon. For my application to comply with regulations, I need to...
On iOS 18 beta we faced a random issue: creating CBCentralManager doesn't trigger BLE permission dialog. There is a thread about this on Apple forums .
Freshly installed...
Dear support team, I see that the mater/Template (Release) example only needs 715K of memory, as shown below:
I want to use nrf54l15pdk/nrf54l15/cpuapp to compile a firmware...
I am experiencing an issue to reach the ADC Max value(4200mV) on the nRF5340(our custom board) . We are using a 12-bit ADC, 4.2V and received a reading of 3297 mV, but we...
Well, this one took me many hours of tracing to track down the root cause, so I hope it helps someone!
Note: I wasn't able to reproduce this directly with a sample included...
I'm trying to debug on the Thingy:53 platform using an Nordic DK as the J-Link intermediate. However, with NCS 2.6.1, adding ` CONFIG_DEBUG=y` to the project configuration...
I am programming with the nRF52840DKs. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am currently working on integrating...
Hello,
I am using the nPM1300 in my hardware design along the nRF52840 and a battery from Renata (ICP622540PMT) . All the power outputs of the nPM1300 are in use (LDO1...
Hi! We are currently in the process of migrating our nrf5 SDK code to NCS, on nrf52833-based hardware. After being stuck for a while on the basic init process of MCUBoot,...
Hi everyone, I haven't found any discussions on this topic yet. I'm trying to flash my nRF52840 custom board, which I bought on AliExpress. It's named "nRF52840 SuperMini...
Hello ,
Is it possible to possible change/disable the BLE services at runtime in zephyr ?
For eg. we have services A,B and C in normal operation and we want disable...
I'm having 3 issues with I2C: A) It keeps returning -5 (-EIO), failed to write to I2C device..., however I do sometimes see the byte going out so I'm not sure why it always...
Hi, I'm working on nRF5340 Bluetooth LE peripheral (building environment: NCS 2.6.1, Zephyr 3.5.99). The net core is populated with the Zephyr HCI RPMsg sample LE Controller...
