Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello,
I am continuing to work on my project with the nRF54L15 DK and have run into another challenge. Currently, the issue is storing images (320 × 492 bytes) in an external...
In the process of obtaining DNV approval for products equipped with modules including nRF24L01+, I have some questions about wireless communication.
1. Does nRF24L01+ meet...
We are facing an intermittent issue on an nRF52832–based product using bare-metal Nordic nRF5 SDK (non-NCS, non-Zephyr) BLE implementation.
Observed behavior:
BLE initializes...
Hey,
I am plannign on developing a locator tag and I wanted to find some more precise information on when to use AoA and AoD and if it changes the accuracy drastically....
Hi,
I need to save a 16 bit counter into a retained register.
I cannot use the 2 GPRETREG since they are already used and I cannot write internal flash.
I cannot use...
Hi everyone,
I’m facing a linker issue in NCS v3.0.2 while using the Zephyr HTTP client sample with TLS enabled , and I’m looking for guidance on the correct configuration...
Hi all,
On a BLE project I was working using version 2.5.0 of the VS Code dev environment I was able to set up a partition where I could store non volatile data, such as...
Hi guys,
I've been using the ADC with the internal reference of 0.9V.
However, to increase the scale of the ADC without using the gain 1/4 I've made a revision to the...
Hello,
we are testing the BLE ADV capabilities and also MESH performances on NRF54L15.
We verified that, in conditions of continuous scanning (interval = 30ms), the packet...
Description: I am implementing USB Mass Storage with a FAT filesystem on external MX25UW63 flash (via EXMIF) using the nRF54H20 DK (NCS v3.2.0).
Setup:
Board: nRF54H20...
Hi Nordic Community, I am working with the nRF52833 and I have a question regarding the electrical characteristics of the dedicated USB signal pins (D+ and D-) when the USB...
I thought that the nRF21L01 had been obsoleted and replaced with the nRF21L01+, but digikey doesn't list the + version but still shows the old one for sale. Has the part been...
I'm sending HCI command LE Set Transmit Power Reporting Enable with both local and remote reporting requested.
The Bluetooth Core Specification says "If the Remote_Enable...
On nRF54L15 DK (CPUAPP) the app boots and advertises fine, I bound my phone using nrfconnect but when I reboot the DK and try to reconnet using nrfconnect, the device hangs...
