My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi! This is a general info post since i have found a temporary fix to it, but whilst trying out ntn, we noticed that when switching from %XSYSTEMMODE: 0,0,1,0,0 to %XSYSTEMMODE...
Hi, we use BMD-350 modules (nrf52832) in our product which has been in production for over a year. Our DFU service is very well tested.
a couple weeks ago, while performing...
I'm planning to deploy a Thread network with 200-400 units and seeking best practices and real-world experience from the community. While the Thread spec allows up to 32 routers...
Hello Support team,
I have an issue with two simultaneous heaps in my project. I use nrf Connect SDK 3.2.2 with the next configuration options:
CONFIG_REQUIRES_FULL_LIBCPP...
Hi,
we are developing on nRF54L15 using NCS v3.2.3 , and evaluating a DFU architecture based on:
MCUboot
firmware_loader
main application
using the BLE MCU Manager...
Hello
I'm currently working SDK upgrade from ncs v2.6.4 to v3.2.1
I found that, in fade in/out scenario, the PWM works well. however, if it need to turn on in 100%duty...
Hi Nordic Team, I am the beginner on this platform. I am trying to hear the PDM mic data in headset on nRF5340 Audio DK. Is it possible to do?
Please guide me as soon as...
When using jlink to connect to my board in VSCode, it displays "unknown device"
nrfutil device recover
I tried a few of my boards, but the result was always the same...
Hi everyone,
I’m working with Zephyr 3.2.3 in a Windows environment and trying to run the shorter connection intervals sample: https://github.com/nrfconnect/sdk-nrf/tree...
Hello Nordic Team,
We are trying to test an external audio DAC (TLV320DAC3100) using the nRF9151 DK .
As a first step, we attempted to build the i2s_output sample from...
Hello Nordic Team. I'm currently facing an issue when building in release mode (CONFIG_LOG, SERIAL, CONSOLE disabled). The issue is that after a random time (no longer than...
As shown in the figure below, I measured a voltage of 5V at the location marked in red, and measured a voltage of 0V in the components within the yellow box。
Is it absolutely...
What is the switching frequency of the internal DCDC in 54L15? What is the function of the FB1 ferrite bead in the reference design? Are there any risks in changing the capacitance...
I am extending one of Qorvo's UWB platforms.. adding Softdevice BLE functions.. (which work ok) (this is on sdk 17_1_0)
the coprocessor uses a GPIO connected signaling mechanism...
Hello!
We are a student group from NTNU which is developing an BLE Audio Beacon using the nRF54L15 socket and the nPM1300 PMIC. However, we have ran into some issues when...
