Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I use examples : nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs;...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
I am trying to source nRF5340 chips from Digikey.
I can see the link to the early Enggineering A version (AB0), which we absolutely do not want to buy
https://www.digikey...
I tried to upload the hello world program to the thingy91s nrf9160 via nrf connect programmer app over usb. Unfortunately it didn't work as excpected and the nrf9160 doesn...
Hi Nordic Team, We are considering basing our next design on nrf5340. nrf5340 implements direction finding: is it possible to use direction finding to estimated the distance...
I connected a button to pin 27 on board, and using app_button_init in app_button.c to declare a button, and use that button to control LED and it does not work. But when I...
Hey all
For my project, which is using the nRf52840 as a Bluetooth server, I have to implement a test software. This test software has to, among other things, to send...
Hello,
I've been given the task of porting an existing application from the nRF52840DK to a nFR52840 Dongle.
Simplified, the application uses the Shell functionality...
Hi,
I run ble_app_hrs freertos on PCA10056 DK board and cannot enter low power consumption. Do I need special settings to use freertos to enter low power consumption?
The...
Hello ,
I'm using ncs v1.5.0 , SUPL client library v0.7.0 and modem FW mfw_nrf9160_1.2.3.
It seems that if I am accessing the Flash area in my application and afterwards...
Hi Nordic Team,
Summary: We would like to know about exact packet details for application model specific
Based on mesh profile doc(MshPRFv1.0.1.pdf) we derived the access...
Hi ,
nRF5340 has hardware support with AES CCM mode encryption. As per product specification document AES - CCM is in built in nRF5340 SoC.
I did not find sample code...
Howdy!
This error message has suddenly appeared on a previously fin Windows 10 machine. My software is all current as of today.
Any hints on what to do next?
Thanks...
Hi,
We want to work on BLE mesh topology using nordic nrf-833 boards. We want to implement mobile application in react native to support BLE mesh features. Please let us...
I was using nRF Connect (v3.6.1) to communicate to Segger J-link Base (version 11.0) but it failed. The error message was: ""Failed to setup device: No serial port available...
