Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi All,
I am trying to migrate my toolchain/sdk v2.4.1 project to toolchain/sdk v2.5.0. And I am having these weird issues related to mbedtls. The same project without any...
Hello,
We tried using pcd_network_core_app_version() to read the network core version (presumably set by CONFIG_FW_INFO_FIRMWARE_VERSION in our hci_ipc.conf) from the app...
Hello If CONFIG_FOTA_DOWNLOAD_NATIVE_TLS is defined in the function fota_download_object_init() the variable dlc.set_native_tls is set to 1 and then in the function download_client_init...
Hi,
I think, I found a missing configuration in the QSPI driver for the nrf53 in nrfx_qspi.c. I've stumbled off this, while I was trying to configure MCUboot for the external...
We are working on a Zigbee-based network coordinator using the nRF52840. Our end device is connected to the coordinator, but when the end device leaves the network, it sometimes...
I am trying to understand why my spi_dt_spec doesn't get the right pins when I use the SPI_DT_SPEC_GET ( DT_NODELABEL (kx122_spi), SPI_OP, 0 ); macros. I tried to expand it...
Hi,
I'm using an nRF9160DK v1.0.1 (2021.26) for developing an application using the virtual COM ports for logging. All of a sudden, I saw that my console showed that the...
Hi ,
I am trying to integrate LSM6DSL to BL5340 module(laird connectivity) through SPI but I am getting failed on initialization. I am noob to NRF so could someone please...
Hi all,
I've build my own board with nrf9161 LACA, so for now I've tried to create my own board, for the moment I'm just trying to pilot my 3 leds. I've follow dev academy...
Hi, I'm building an application that will use the nrf9160 as a middle man for a websocket connection that becomes a uart connection on the main processor. Thus I want to receive...
Hello there! I am working on a central-peripheral connection, where sometimes the central is not receiving notification(s) from the peripheral. The central then asks for a...
Completing the nRF Connect SDK Fundamentals in the DevAcademy, I stumbled across this question:
Why is true not a valid answer here? Running gpio_pin_set_dt(&led, true...
Hi,
I was following the beginners tutorial and things were fine till i reached the section to create a project from scratch. I was able to build this project as well.
...
Hello,
I'm curious if there is a dependency to use the same Bluetooth module to perform OTA. If I created my own custom board, would I need to use an identical Bluetooth...
